Not so much Dv pulls, but dr unit waste toner backups. Causing a clot at the front drop port and backing up from there, causing L4 19's, blade flips and such.
Type: Posts; User: Nachoman4life
Not so much Dv pulls, but dr unit waste toner backups. Causing a clot at the front drop port and backing up from there, causing L4 19's, blade flips and such.
OK, would take a closer look at the C, M, Y DR unit (a bad dv pull (even from the color on the left, as the Pri trans can carry and drop dv too), Dr damage can be hard to spot, if a damaged dr is...
I have had a few of these throw similar errors, and F2 during normal use and, image density/registration errors when calibrating. The primary transfer cleaning unit has a stirring mylar in the...
OK, expand our oil production, still doesnt change that the refining production is already at 100%, if oil sitting in holding tanks with no where to go decreases gas prices Im all for it.
Yes I have seen something like this on an ARBC320, many years ago, I had a mouse pee damaged Color ASIC, on the ICU (now the SCU pwb). Yours may not be mouse related, possible a staple fragment, or...
The foams are replaceable, you do have to break the unit down to get the idle rollers out , usually takes about 15 min on average, much cheaper to spend 15 min over a unit cost. It stinks having to...
Lexmark (or who ever they bought the design from (as they buy designs from others) scanner disassembly/access is absolutely horrible) Pure FN s#!t, why does it take 30 minutes of covers, removing...
If you remove a finisher, from a newer sharp and do not replace the foam rings on the lower exit idle rollers the paper will curl downward, and cause exit fold over issues.
The M7570 fusers have been a pain to us also.. New machine fusers make the first 300k, but after the 1st rebuild have been some trouble for us also. Have 2 mxm7570 in a bank (70 miles away), 50 ft...
Given its a school, probably alot of coping with the feeder open, books, smaller originals, causing a dark lead edge. I agree increasing the lead edge margins a bit is a good idea, have had to do it...
A 22-6 and 23-2 would help alot, if you can provide them...
Just my first time taking a vid of them cold, have had it happen before also.
As for thermal contraction, I believe the hub is affected more than the neoprene rubber is making the roller come off of...
Literally put them in my armpits to warm them up enough to work, the prefeed roller was new also, the right most one was room temp. Not the first time the cold has done this....
An EMMC/MSata/SD read failure can cause a reboot loop (Read errors?) , if so try a new MSATA/SD ((no known way to clone EMMC as far as I know, MSATA/SD can be) , (Bought third party and cloned with...
The glass cleaner I mostly use is a summer mix of 30% alcohol, and 69% (Nice) windex, with several drops of light silicone oil (fuser oil) to make the last 1%. Winter mix, I reverse the mix...
onboard, aka surface mount, so even if I could get chips, dont have the the hardware to reflow a BGA chip to the board.
so mfp replacement.
I have had both a color and an M version do this, both ended up needing MFP pwb and emmc, a co worker called it into DSSD and they hinted at failure of the onboard ram.
I take no bonus, or commission, in fact disagree with cutting corners because of....
PE and BEI give confusing answers, and charge alot for it.
Its MLM, as far I can tell. Its mostly about the...
A freeze on the please wait screen has been a symptom of the "Expansion/Caching memory" ie.., the SD card, Msata, or EMMC for a long time.. A few early signs of it starting to read fail are, slow...
google "eurion constellation", its on cash and some higher value checks
I have had a handful of these that were due to a failing separation motor, something to keep in mind if it comes back.
The hacked HP pics of Mayonnaise Low and Mana Low are some of my favs..
Try direct to the wall for a week or so, some surge suppressors, are the problem, its a one week idea to check
Bad surface for the pic, maybe put it on a piece of standard rule paper.
At least for me, its not been a huge issue, have replaced 4 thermostat harnesses, that were obviously open circuit, but its annoying, for sharp to suddenly move to non reset-able stats. I have taken...