Search:

Type: Posts; User: Nachoman4life

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    1,574

    [CQ] Re: Phoenix CR4/CR4.5 - Dev Pulls

    Not so much Dv pulls, but dr unit waste toner backups. Causing a clot at the front drop port and backing up from there, causing L4 19's, blade flips and such.
  2. Replies
    7
    Views
    1,097

    [Misc] Re: Sharp MX-6051

    OK, would take a closer look at the C, M, Y DR unit (a bad dv pull (even from the color on the left, as the Pri trans can carry and drop dv too), Dr damage can be hard to spot, if a damaged dr is...
  3. Replies
    5
    Views
    3,664

    Re: sharp MX-3570N

    I have had a few of these throw similar errors, and F2 during normal use and, image density/registration errors when calibrating. The primary transfer cleaning unit has a stirring mylar in the...
  4. Replies
    1,653
    Views
    178,618

    Re: $5.00 per gallon gas

    OK, expand our oil production, still doesnt change that the refining production is already at 100%, if oil sitting in holding tanks with no where to go decreases gas prices Im all for it.
  5. Replies
    7
    Views
    1,191

    Re: Green glow only on color scan

    Yes I have seen something like this on an ARBC320, many years ago, I had a mouse pee damaged Color ASIC, on the ICU (now the SCU pwb). Yours may not be mouse related, possible a staple fragment, or...
  6. Re: MX-4070V - ERROR L4-11 - Removing Finisher

    The foams are replaceable, you do have to break the unit down to get the idle rollers out , usually takes about 15 min on average, much cheaper to spend 15 min over a unit cost. It stinks having to...
  7. Replies
    8
    Views
    1,293

    Re: Lexmark XC4140 - Scanner - Lint /fuzz

    Lexmark (or who ever they bought the design from (as they buy designs from others) scanner disassembly/access is absolutely horrible) Pure FN s#!t, why does it take 30 minutes of covers, removing...
  8. Re: MX-4070V - ERROR L4-11 - Removing Finisher

    If you remove a finisher, from a newer sharp and do not replace the foam rings on the lower exit idle rollers the paper will curl downward, and cause exit fold over issues.
  9. Replies
    23
    Views
    5,404

    Re: MX-M7570 POD!-N POD1_NA random jams

    The M7570 fusers have been a pain to us also.. New machine fusers make the first 300k, but after the 1st rebuild have been some trouble for us also. Have 2 mxm7570 in a bank (70 miles away), 50 ft...
  10. Replies
    23
    Views
    5,404

    Re: MX-M7570 POD!-N POD1_NA random jams

    Given its a school, probably alot of coping with the feeder open, books, smaller originals, causing a dark lead edge. I agree increasing the lead edge margins a bit is a good idea, have had to do it...
  11. Replies
    23
    Views
    5,404

    Re: MX-M7570 POD!-N POD1_NA random jams

    A 22-6 and 23-2 would help alot, if you can provide them...
  12. Replies
    4
    Views
    860

    Re: Cold Mx 850rt

    Just my first time taking a vid of them cold, have had it happen before also.
    As for thermal contraction, I believe the hub is affected more than the neoprene rubber is making the roller come off of...
  13. Replies
    4
    Views
    860

    Cold Mx 850rt

    Literally put them in my armpits to warm them up enough to work, the prefeed roller was new also, the right most one was room temp. Not the first time the cold has done this....
  14. Replies
    9
    Views
    2,918

    Re: Sharp MX-4050 Restart Loop

    An EMMC/MSata/SD read failure can cause a reboot loop (Read errors?) , if so try a new MSATA/SD ((no known way to clone EMMC as far as I know, MSATA/SD can be) , (Bought third party and cloned with...
  15. Replies
    11
    Views
    1,183

    Re: General MFC question.

    The glass cleaner I mostly use is a summer mix of 30% alcohol, and 69% (Nice) windex, with several drops of light silicone oil (fuser oil) to make the last 1%. Winter mix, I reverse the mix...
  16. Replies
    9
    Views
    2,918

    Re: Sharp MX-4050 Restart Loop

    onboard, aka surface mount, so even if I could get chips, dont have the the hardware to reflow a BGA chip to the board.
    so mfp replacement.
  17. Replies
    9
    Views
    2,918

    Re: Sharp MX-4050 Restart Loop

    I have had both a color and an M version do this, both ended up needing MFP pwb and emmc, a co worker called it into DSSD and they hinted at failure of the onboard ram.
  18. Replies
    8
    Views
    1,231

    Re: Pros Elite, What do you think of it?

    I take no bonus, or commission, in fact disagree with cutting corners because of....
    PE and BEI give confusing answers, and charge alot for it.
    Its MLM, as far I can tell. Its mostly about the...
  19. Replies
    13
    Views
    2,926

    Re: sharp mx3050n

    A freeze on the please wait screen has been a symptom of the "Expansion/Caching memory" ie.., the SD card, Msata, or EMMC for a long time.. A few early signs of it starting to read fail are, slow...
  20. Replies
    11
    Views
    1,898

    Re: Sharp mx m 654N

    google "eurion constellation", its on cash and some higher value checks
  21. Replies
    8
    Views
    1,111

    Re: L4-16 code on a MX4141N

    I have had a handful of these that were due to a failing separation motor, something to keep in mind if it comes back.
  22. Replies
    9
    Views
    1,307

    [Funny] Re: Amusing Display Messages

    The hacked HP pics of Mayonnaise Low and Mana Low are some of my favs..
  23. Replies
    9
    Views
    1,665

    [Electrical] Re: Showing N9 on ESP surge protector

    Try direct to the wall for a week or so, some surge suppressors, are the problem, its a one week idea to check
  24. Re: Parts came out of MX-pn14 punch unit

    Bad surface for the pic, maybe put it on a piece of standard rule paper.
  25. Replies
    13
    Views
    6,082

    Re: MX-3050N showing H2-01 error

    At least for me, its not been a huge issue, have replaced 4 thermostat harnesses, that were obviously open circuit, but its annoying, for sharp to suddenly move to non reset-able stats. I have taken...
Results 1 to 25 of 213
Page 1 of 9 1 2 3 4