wait.. your machine runs without CMY drums or developer units? whoa!
Type: Posts; User: bronco31
wait.. your machine runs without CMY drums or developer units? whoa!
BC again on point! and Subaro.. thanks.. yes the drums were damaged
I swapped one DK5195K drum from next room over 308ci to test..Lo and behold! black band defect front to rear is gone.
I...
when printing 2 status pages.. defect is shifted.. BW copies get a Black defect line
you say it happens on copies too? Yes
reduce the image by 50% do the lines shrink with the image? ...
BC.. the distance between each color band/defect: 96.5mm... drum diameter !
but my tired brain cant come to a conclusion why or how this info helps narrow problem to the cause..
"drum/dev and...
1mm banding..not random, has a pattern to it.
Kyo hotline thinks its Hi-Voltage PWB.. or Main PWB.
I think the Main pwb is big part of logic/data into dots...data crunching into laser output...
TA 358ci, 97K count, no surge supp connected..had a AC power dip/spike in the building, ( wasn't printing or copying during surge).. it rebooted, showed no codes.. no clicks, no abnormal...
is it because the OEM fuser roller has a poor quality "teflon" non stick coating ?
green4go..." when I hook up my laptop with a server 2019 vm" SKILLS! :)
Fixed.. (it took another techs eyeballs and superbright LED) Amazingly...a paperclip worked its way past the rear cover , into the rear drive section.. and got caught and stretched around an...
ok Thank you..will look at both A782711901 and A782890111 .. yes i first fed a cardstock thru... got staples and 1 paper clip out.. thought the call was done.. nope! ;)
working on a Konica C450i with DF713.. paper passes .. but consistently Z folding the originals.. paper crunching sounds..until it jams.. mostly J66-14.. or 66-05...
Feed tires good..blew out...
also here..various office Kyocera unable scan to O365
im hazy on server vs client side..whats the difference.. the Kyo Command Center Guide under Network Security Settings (to turn on/off SSL3...
i cant find the Load Check in the BH808 Service manual for running M5, the paddle motor.. in the FS=536 finisher?
will double check APS enabled Tray 1 and 2.. and Group cassettes thru web portal.. thanks all
(so much of our job is tuning) ;)
Tray 1 and 2 both normal Letter ... incoming faxes over the weekend uses all tray 1 paper.. and doesnt ATS to tray 2... (but does ATS for a copy or print job)...
customer is hurt and offended
whats BD again? (its on the tip of my brain)
whoa weird Mita! You vacuumed out the toner hopper and put developer in ? Then did you have put a new toner cartridge in?
I am used to Konica.. like a Bizhub601..at PM..But it'd be the dev unit...
wait ok BC.. again im lost...
Dual component i thought meant separate toner and developer.... And Kyocera developer/carrier premixed inside the toner is mono component.
im still hazy on CASS.. so a new Kyo dev unit comes with carrier in it?
Kyo is mono component... is toner premixed with developer right?
if its same as it used to be.. man is the setup tool clunky ! half the time i couldnt get it to work and not intuitive at all
poor fella.. id be just as clueless if i was expected to speak and function in Swahili ;)
"compress together, but it sure seemed like the toner had hardened form melting. I dunno."
i seen Kyo toner turn into hard little chunks of rock just from backing up in the auger.. imho, i'd say...
you cant scan over USB, only over the IP network ;);)
so a 25xxci is really a firmware crippled 35xxci ;)
just print from a usb drive?
Yes calibration huge mystery to many of us !
Also on my mind a question:
Heres the latest Kyocera out in Europe: TASKalfa 3554ci
If this is the FOURTH...