Search:

Type: Posts; User: Zackuth

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Welcome!

    by Zackuth
    Replies
    10
    Views
    1,270

    Re: Welcome!

    Welcome!! This is a great site. I have learned a lot here.
  2. Replies
    4
    Views
    6,891

    Re: Bizhub C550 - blank screen

    This happened to me, I think it was the main board that went out. Had to relpace the board and reload firmware. Reloading the firmware was an adventure in itself.
  3. Replies
    3
    Views
    1,322

    Re: Welcome boot screen taskalfa 250CI

    I had one like this. After doing everything according to the troubleshooting guide and a few suggestions from tech support, it turned out that the problem was one of the boards in the op panel. I...
  4. Replies
    10
    Views
    1,460

    Re: Programable tech messages.

    Replacing the toner will not fix jamming issues so don't try.
  5. Replies
    2,338
    Views
    1,645,711

    Re: The random thought thread

    I'm not sure what #9 Crazy Eddies is, but I'm sure I've heard about it as something else. All the rest I remember, and I drilled a hole in a subway token from Boston back in 1983 and put it on my...
  6. Replies
    6
    Views
    3,609

    [CQ] Re: Yellow lines Kyocera (utax) 5550ci

    I've seen lines like that on the b/w machines and it turned out to be the developer. Resetting the values in the maintenance mode to the initial setting helps sometimes, other times we have to...
  7. Replies
    7
    Views
    1,056

    [People] Re: This to all those who served

    Thank you to all the Vets out there, your service is very much appreciated!!!!
  8. Replies
    12
    Views
    2,283

    Re: Bizhub C550 no response

    That code means the cyan TCR sensor adjustment failure. You can try cleaning the sensor if that doesn't work you'll have to replace the cyan imaging unit.
  9. Thread: Just wondering

    by Zackuth
    Replies
    13
    Views
    1,408

    Re: Just wondering

    My company sells Kyoceras and Knoica Minolta, both are good brands. Kyocera is easy enough to learn, you should be just fine if you accept that new position.
  10. Replies
    3
    Views
    1,007

    Re: C-c163 in bizhub c451

    The first solution is to replace the printer control board and update the firmware. To update firmware in these machines you have to get a program from the Konica Minolta website that formats a CF...
  11. Replies
    3
    Views
    2,186

    Re: C6950 on a 7550ci

    I had a C6950 error on a 3051ci, turned out to be the low voltage board.
  12. Thread: C6950

    by Zackuth
    Replies
    8
    Views
    19,090

    Re: C6950

    I had this on a 3051ci machine turned out it was the low voltage board. Check voltages on the board and see it the outputs are correct. I had no 24v outputs at all.
  13. Replies
    4
    Views
    753

    [Misc] Re: B601 ID sensor board part number

    The ID and gamma sensors are on the toner control sensor board. Part # 56AA-9102E. You might want to clean both sensors before ordering a new one. Most times that works.
  14. Replies
    26
    Views
    3,333

    Re: *&% you Ricoh engineers! (rant)

    IF that many go back in.
  15. Replies
    2
    Views
    2,029

    9330CDW Fuser Heat Roller

    Hi there. Does anyone have the part number for the heat roller (and a good supply source) for a 9330CDW? I have looked on line and can get the fuser unit (pressure roller) but I need the heat...
  16. Re: KM 5050 New Operation Panel and Now Old "Dead"

    The ribbon connector for the touch screen sometimes can get moved out of the connector when installing the panel (maybe this just happens to me). I would check that and reinsert if out or not in...
  17. Replies
    5
    Views
    1,087

    Re: KM/CS 500ci Lines on drums

    This happened to me on a 300ci. I wish I could help out but I kept cleaning/replacing drums until the problem went away. I changed drums, developers, transfer belt and I believe the drum motor. ...
  18. Replies
    12
    Views
    4,446

    [Misc] Re: bizhub 600 "Now Warming Up Ready to Scan"

    There are three lamps, two in the heat roller and one in the pressure roller. All three have to be on for it to work right. If you have only one lamp on in the heat roller then you have found the...
  19. [CQ] Re: Hello, I'm user of your Konica Minolta BizHub 600 printer, and i wonder if you c

    You could buy the print accessory and get the machine to print, but support for this machine ends March of next year (meaning no more parts will be available). I would get another machine.
  20. Replies
    5
    Views
    1,091

    Re: FS 1128 feeder jam 70

    The DP cord might be the cause, the cord on these and the FS1135's will cause issues that are intermittant. You might want to try the cord.
  21. Replies
    5
    Views
    2,063

    Poll: [Misc] Re: C451 serious noise problem

    I had a noisy C451 and it was the black image unit, which to me sounded like it was coming from the fuser area. It was jamming and finally gave an error code, I don't remember which.
  22. Replies
    2,338
    Views
    1,645,711

    Re: The random thought thread

    Cool!!
  23. Replies
    65
    Views
    12,520

    Re: Broken heart and pockets

    Best wishes and a full and speedy recovery.
  24. Replies
    9
    Views
    1,122

    Re: ok I am done with C451's

    We have 4 C452's in the field and have very little issuses with them.
    You're headaches will not get any better if you get a Kyocera 250ci--or any Saturn type machine.
    Can't comment on the Canons,...
  25. Replies
    32
    Views
    95,209

    [Error Code] Re: error code 0094 on a Konica Minolta C35

    Thank you!! This was my problem and removing the pad looks to be the answer.
Results 1 to 25 of 450
Page 1 of 18 1 2 3 4