Search:

Type: Posts; User: turbojetboy

Page 1 of 12 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    1,134

    Re: mpc2050 removing paper feed unit tray 1

    Its not that big a deal, but you will want to have a new "spring clutch" on hand. I tend to replace both trays "spring clutches" whilst im there. It usually takes about an hour. Its the spring and...
  2. Re: mp c3002 & 5502 cycles fuser in energy save mode about every 30 seconds

    Check Sp mode 1151 values 2 3 & 4. Some machines where sent out with the INITIAL value incorrect (somewhere around 2,500 instead of approx 500 to 800). I had on that was correctly set to its intial...
  3. Replies
    5
    Views
    920

    Re: RICOH MPC4000

    It will almost certainly be the IH inverter board, behind cover to the right of the fuser assy.
  4. Re: Ricoh MPC6501 - blur first 200 prints in the morning

    I have seen it many times, and have found in most cases I have had to replace both coro assy and that actual drum. I think it is not moisture but some sort of ozone gas issue causing a reoccuring...
  5. Replies
    4
    Views
    1,002

    [Misc] Re: Mpc 7501 fusing unit

    I have used both in either model. Only difference I can see is that you have to make sure the little loop wire on the upper rear connector assy matches the model type - justbswap one end of the loop...
  6. Replies
    11
    Views
    1,890

    Re: C5502A CIS MALFUNCTION

    I havent seen seen it personally, but I have heard of it and apparently in most cases it is a corrupt Nvm value associated with the Cis, might be worth running thru these values first looking for one...
  7. [Misc] Re: Printing Problem in Ricoh Aficio MP C2030

    On the left side panel is a red switch, turn this switch off.
  8. Replies
    5
    Views
    842

    [CQ] Re: MP C 4502/5502

    Extremely common fault on this range. There are bulletins with dozens of Sp mode changes and this issue is mentioned in firmware. However even when all these measures are applied this is still very...
  9. Replies
    3
    Views
    490

    Re: C3300 and C4501 ITB

    These all seem much the same thru the range up to and including the MPCxxx2 series. You just need to swap the top covers of the assy over and it should go right in no problems. The belts are all the...
  10. Re: Problem to clean the laser optics unit

    [QUOTE=Killeromantic;493199]Hello I started to clean the optical drive of a spc820 Ricoh laser to remove and clean the mirrors and reassemble the inaccuracies I are blurred.

    It seems to me that...
  11. Re: Problem when adding new Developer to Ricoh MPC 6501 MPC 7501

    Check the photointeruptor on the rear of the itb assy that checks the poistion of the blue transfer handle. These can become dislodged etc.
  12. Replies
    14
    Views
    5,373

    Re: Ricoh C6501 Toner cartridge Empty

    You will almost certainly need to replace the Y dev mix, and to be honest probably a hell of a lot more than that. Unless you REALLY know what your doing here this will end badly.
  13. Replies
    10
    Views
    14,336

    Re: package_all Firmware

    Not a fan of the package firmware. It seems quicker - and it is....because it only updates main frame firmwares, so adf, finishers etc are not updated. I have stopped using it for this reason. Whats...
  14. [Misc] Re: how to print directly from a usb stick to machine

    I think the Usb/Sd option box for the models you are talking about is only for allowing scanning to Usb/Sd card. I could be wrong here, but I have not seen these earlier models support printing from...
  15. Replies
    5
    Views
    1,605

    Re: Ricoh Sp c811 have a sc 548

    Most likely its the sensors upper left side behind small upper cover that detect fuser and ferrite rotation. Replace with the modified types Aw020190. 15 minute job.
  16. Re: Ricoh C6000 not able to do the DV setup procedure?

    Little blue handle needs to be in downwards position when loading devs, you get this message if its in the raised position (put it back up when reinstalling hopper). Its possible the sensor that...
  17. Replies
    2
    Views
    555

    Re: C7501 "set fuser correctly"

    The fuser has a link wire accross 2 pins at the rear upper connector on the fuser itself. My bet is you have a problem on the fuser connector top rear just under the plastic top lid. Also note this...
  18. Re: Ricoh MP C5501 w/50k...Turd at any count or did I find me a diamond?

    Mpc 5501 are in my opinion best colour midrange mfd that Ricoh has made to date, super reliable easy to fix and parts run to PM and then usually way past.
  19. Replies
    11
    Views
    1,835

    Re: MPC 3300 Toner pump conector

    You are most likely going to have to remove the entire drive assy ( done this many times before due to gear failure). Its a big job with a lot to remove. First time it took me about 4 hours all up,...
  20. Replies
    9
    Views
    1,908

    Re: Ricoh mp c3002 Black marks

    Seen a lot of this, although usually the first drum to get these strange sticky marks in my experience is the Y drum. Only happens to machines that have high volumes on the drums, so they are well...
  21. Re: MPC2800/3300 display dead (mirror motor and BICU did not fix)

    "Surf the machine" and see if you can access Wim, then look for errors. (Key in mc Ip address into browser of connected pc).
  22. Replies
    5
    Views
    1,099

    Re: Ricoh Copiers

    There is! I just program in a 2 mm erase margin all round and set that as the default for scanning, dead easy. Gets rid of that pesky line on the very edge of some docs.
  23. Re: MPC 4503 with SC670 and Turning Itself Off/On Randomly

    I cant recall where I read this, but I believe there has been some cases of random shut downs and sc codes due to a faulty mini usb lead that is under the control panel connecting the control panel...
  24. Thread: c5502

    by turbojetboy
    Replies
    17
    Views
    2,166

    Re: c5502

    100% Fuser, even if it looks perfect - thats the way they are.
  25. Replies
    6
    Views
    1,010

    Re: Fuser Issues???

    as others have said, this model was very touchy with this problem. Make sure you are not overtoned on any colour, run all the colour mode calibrations. Model is very picky about paper quality with...
Results 1 to 25 of 283
Page 1 of 12 1 2 3 4