Search:

THANK YOU !!! This fixed the problem, thanks for your help!

It came off the old board so it should be an IC 208

36424 Yes, I believe it is installed correctly.

I'm not able to print a config page, yes the chip is lined up notch to notch. I'm not that familiar with Kon/Min equipment, how do you update the firmware?

I did try that, but no difference.

I have a Konica 601 that was only showing the hour glass on the the screen. I replaced the OACB with a complete used Board, the copier now works normally but I am unable to print to it. I changed the...

I cleaned the sensors and it seems to be working good now.

I never would have guessed that they could be related to the problem.

Thank you!

Konica/bizhub 750 I put an original on the glass or doc feeder and press start and it will say printing, but nothing is happening. I can turn of the main switch for about 5 minutes then turn on and...

Xerox 510dp, keep getting a LL-0c code. It can reset by turning off an on the printer - white switch only, and will be ok for a day or so. I don't see the code in the manual.
any ideas on what is...

I have a Riso RC6300 that has a T2 code. The fuse was blown on the power supply (F12), I replaced it and the machine kind of blinked off and on several times then the tray went down. Now it won't go...

yea thanks for the kind response. sometimes konica hides that info or words it so you can't tell that its a reset. I was just looking for a quick fix as I am new to this machine. I have done some...

I'm looking thru the manual, I can't find the way to reset a trouble code. How do you do it? where in the manual does it show this?
Thank you

I'm getting a code c3851 on the Konica c252.
Can this only be reset with a new fuser unit or replacing the pico fuse?

would you also say the copy qualilty is the same or better. Is there a source for rebuilt bizhub fuser units.
Do you also like the c350 and c450 series of machines?

I looking at some used equipment and I could use some information and Help. If you had a choice between a Canon IRC3220/5185 or konica-Bizhub C252/c452 which would you pick and why?

Thank you

What is the difference between the Canon IRC5185 or 5185i ?
At about what copy count does this type of machine become less reliable/needing a lot of parts?
I'm looking at a 5185i with 926k on the...

1357713578
First image is after ten copies, 2nd image is the second copy off of the copier. both sent from computer not off of the glass.

Thank you for your help. I removed and clened the salt sensor, the copier gat past the E020-225 then went to a E20-0434. After looking at some other forms it looked like the Black unit was defective...

I was getting an E020-0225 code at start up in the mornings, also after about 20 copies bands of magenta and yellow background. I replace the drum units with remanufactured units except for Cyan is...

Sensor checks ok. the macine will run 1 to 50 sheets before error. never any damaged, jammed or stuck paper.

I have a Xerox 510dp wide format copier and I'm constently getting error E4-01 false fuser jams. I've cleaned the contacts for the fuser drawer, no change. Does anybody out there know what is causing...

:confused: I currently have a Canon CLC5100 with a about 2 mil on the meter,starting to have a lot more problems. I am thinking of replacing it with a used 5185i with 386k on the meter, is this a...

I went in and did the ram-clear and entered info. found SALT sensor was bad, the yellow was still swapped with magenta and the problem changed to it. replaced and now working. How do you run a DCP...

Canon CLC 5000 I'm getting an E20-0387 error after changing all 4 starters. I swaped the yellow drum, developer housing and SALT sensor, no change. SGNL-S, SGNL-D, SIGG-S are all low, REF-S, SGNL,...

I have had this problem and it was the one-way clutch in the gear driving the first shaft into the buffer unit. It was slipping some causing the paper to slow down thru this area.