I've been fighting the same thing on one, Did you ever resolve this?
Type: Posts; User: randall
I've been fighting the same thing on one, Did you ever resolve this?
Check parts catalog for sensor
Figure 771 - WASTE TONER DRIVE DETECT ASS'Y
Note, waste toner drive motor is M45.
Remove waste bottle shine light into cavity, look at rear sensor and switch...
Spark chasin time!
First question: Was any work done on machine prior to the error code?
E197-0100
Fault in communication with laser interface PCB
Swing the control box out and remove the...
Thanks ill check/change the setting this morning and let you know
Welcome
Hi everyone!
As the title says this is wierd. At this machine yesterday cust tells me that it always asks for paper whe you send print jobs.
Explanation, if you send 10 copies of a single...
Thanks mongo, ill check em out. Its the paper pickup drive motor.
I have checked all the usuall parts places no go even sent my motor to hytec and they said couldnt be repaired..shaft was ground to a nub
Anybody have a bone yard with an 8500 they can dig this...
If the problem is in dev unit, you can see the void on mag roller of developer, this is caused by toner chunks in developer. Hopefully your toner and hopper aren't contaminated with chunks...this is...
This unit has a shared
DEV. H.V. PCB ASSEMBLY, COLOR, FM0-2938-000
Which is why you only see this fault in all color PG5s as mentioned in your original post but not black.
I would replace this...
imageRUNNER ADVANCE C7260 / C7270
Title : Magenta Color Registration is Skewed Causing Lines to be Not Aligning Properly
Problem :
The magenta color registration is skewed causing lines to be...
Thought i would chime in.....
In your last image, it looks like you have a horizontal crack in your fuser film. Look at magenta on your type 10. Replace the film and pressure roller, also may cause...
Pull out the fixing feed tray, remove the registration assembly. There is a sensor flag on the frame underneath it in the paper path on the right about 4 -6inches from the rear of the tray flag...
Clear error code:
Remove empty yellow toner bottle, using flashlight look inside to see if bottle grippers are both open! If not cut coat hanger bend in a hook shape ond reach in to open both...
Heres what i have done that worked...
Scan to file
Are they local pc folder shares or server shares mapped to pc
Print a config page from the 6002
This mostly on older machine not sure on 6002...
It's fairly easy(after the first time) but time consuming approximately 1.25hrs.
1.separate fin and machine
2. Remove inner cover
3. Remove top rear cover
4. From machine side, remove 2 sheet...
Intermittently, the machine will display a 0F75 jam code. The 0F75 jam code references a possible issue with the ITB Assembly.
Workaround :
Go to Service Mode COPIER>DISPLAY>MISC and check...
Customer: what was wrong with it?
Me: (a little to enthusiastically explain) this error code relates to...and....
Customer (blank stare)what did you do to fix it?
Me: (holding out inevitable...
Sounds like communication failure, and you have already changed both logic processing ends (pcb), swap out both comm. cables as either a pin or wire inside may be damaged.
If all else fails, go...
Ok 3v is good, remote signal to relay from all night. Power off and disconnect all loads from relay, leave connected 510,511,512,513,522,523,501,508,507, power on machine
Check to see if you have...
I have this happen on multiples both 5000 and 5200 with only 2 fixes actually working. Forget the "leveling"Feet..also check the bearings and shafts of the steering roller, one side will over wear,...
Macs have a whole bunch of weirdness when it comes to printing color to CYMK devices. And gets more complicated depending on OS version. Also depends if "DESIGNER" knows true color theory and design...
Ok, spark chasing time...
Break out your volt meter
Questions:
1. Is there green power led on control panel lit?
Does it power with doors(main and right) open?
The...
I agree hole heartedly! Damn Mac!
I am having similar issues with all Mac client law office using client codes and maverick (10.9.2). Machine is Canon though. Here is our solution for pop...
Hi all,
I am having a couple of problems in an all Mac environment, I'll break it down by os version. Hopefully someone has a solution other than smash the Mac(whish is where I am at the moment)....