Hi i have the same problem when i changed the solinoid i have a message "please wait machine wearning up" i noticed that the flat cable of scanner assambly was broken i repare it and the machine work...
Type: Posts; User: abdou
Hi i have the same problem when i changed the solinoid i have a message "please wait machine wearning up" i noticed that the flat cable of scanner assambly was broken i repare it and the machine work...
You must reload software you find it in the web site Workplace and Digital Printing Solutions | Xerox via web page or altboot method
HI, I have a problem with fiery when I turn on the fiery the display is blank I hear the fun tourn normally I change the ram prosseseur but I have the same problem :(
You have problem in the hdd tray to format hdd than reload software by altboot method
It's the loading of the software that take a long time not the fuser warming up you can not change this time sadly, The new machine for exemple altalink C80XX take less tame to come ready
Thank you all for your help, I fixed the problme ;) The USB port is loked so I can not load software by altboot procedure so I changed the SD card of a machine that work I load software by altboot...
sorry I find the difficulty to translate in english I try to speak in french " dans ongle image qualité tu doit cocher le mode brillant" you find that with dark or light print
I give to us more specification
first call the custmer changed the toner cartridge but the machine always request to change toner my first intervention I detect that the probleme is in the ATC...
Please can you give the manuel for ricoh 7100 thanks a lot
The 7 segment display atwdicimal point flashing correctely and the two 7 segment in ess display 7 and 0 I think all the componant of the machine is ok but the machine does not boot correctely
Thanks for your help, the machine has worked for 1 mounth and the custmer call for a problem in the toner cartridge the machine does not know the toner cartridge I reseat the NVM value after save it...
I am a tech and I followed the procedure from the manuel first time I install the firmaware using Altboot procedure after I add Forced Altboot file, the problem persists and after I changed the hard...
Hi everyone I have a problem with altalink B8090 when the machine boot he dont complete the boot she arrives until show xerox altalink B8090 and the machine reboot I reload the software change the...
You can eliminate this problem in command workstation you must checked the option bright good luck
You have a problem in exit fan you can test it in diagnostic mode with code 42 036 If the fan dont turned on you must change it if this dont resolve the problem you chage the IOT PWB
HI everyone I am ingeener for xerox copier I need service manuel for ricoh 7100 thanks a lot
Nvm battery is a battry that you find it in the controller pwb in the rear below the scanner
I think that you have a probleme in registation area exactely the registration clutch try to change the registation clutch
You have a problems in the software tray to reload softwre by altboot method if this solution don't fix the problem check the voltage of the yellow battery you must find 2.8V il less change the...
to inter to servive maintenance in xerox 7232 HOLD "0" BUTON FOR 5 seconds and hold green buton after inter password 6789 the NVM value to clear 10-333 IS 744-004 to 0 if this méthod don't inter in...
verify that the exposure lamp is torned one, if non you change lens assembly after ccd flexible cable after iit pwb
if the nylon is brocken in the same place I think that you should check that the developpeur unit is intalled correctely try to emply the developpeur module and intall a new develloper materiel
thanks you all for your responses in site I have 10 machines work with equitrac solution the probleme is in the machine not in equitrac because I have xerox altalink C8045 in the same site the...
it can caused by two problems first you must check the connector of fuser module if he docking corectely or you change LVPS( low voltage power supply) to remove il you should remove the rear cover...
I changed the hvps for black developper housing bias but the same problem the banding is in both copy and print mode other color c m y is fine the probleme in black copy only I repeat I changed the...