Search:

Type: Posts; User: bonnie750

Page 1 of 13 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: POD1_N Error

    by bonnie750
    Replies
    11
    Views
    8,889

    [Jamming] Re: POD1_N Error

    if this is a mxm620 series machine it is going to be the hot roller gear. broken drive peg
  2. Replies
    1
    Views
    666

    [Misc] Re: Need CDFT software

    This isn't a machine to get involved with if you haven't done the course. it is mechanically complicated and needs
    not only cdft but the service and parts manual. a good stock of spares also.

    bill
  3. Replies
    12
    Views
    2,404

    [CQ] Re: mx503n unusual marks on back of page

    if the mark is at the exact same place on every print then it cant be a roller. If its on prints only it cant be optics.
    I thought that maybe the paper had a fault which only showed after its been...
  4. Replies
    10
    Views
    9,417

    Re: Hp cm6040 fuser reset at life end.

    I reset these fusers on a regular basis. Reset once and then change them for a new fuser. A new fuser does not have a fuse installed to be blown on first install.

    bill
  5. Replies
    4
    Views
    1,198

    Re: HP 6030 asking to remove and shake toner

    Is this a Danwood machine?

    Bill
  6. Replies
    10
    Views
    9,417

    Re: Hp cm6040 fuser reset at life end.

    There is no fuse in a new fuser from HP. I can give you info on what fuse to use and where to fit if you need it.

    bill
  7. Replies
    2
    Views
    1,005

    Re: HP CM8050 Color MFP

    HP designed and built the edgeline at a purpose built factory in north America. The finisher was made by a Spanish company and the paper deck is a Xerox product. The machine did not sell as well as...
  8. Replies
    5
    Views
    1,171

    Re: F1-17 mxm850. (Mxfnx5 finisher)

    hey Andy any luck with this one mate?
  9. Replies
    10
    Views
    1,520

    Re: Mxc311 thoughts?

    I agree with all those comments. The fuser is a pain to rebuild, about 3 beers I reckon!
    i've got a spare which i use and then repair the faulty one as required, usually 1 to 2 beers.
    the cam which...
  10. Thread: scanning

    by bonnie750
    Replies
    2
    Views
    729

    Re: scanning

    thank you for that. just can't get my head round this one. i will get there and try try your suggestion

    regards

    bill
  11. Thread: scanning

    by bonnie750
    Replies
    2
    Views
    729

    scanning

    has anyone setup scan to folder on a laserjet 5035 using two network cards? I can set up to print with both from 2 networks but as soon as scanning is enabled authentication fails..
    Any...
  12. Thread: F2-39

    by bonnie750
    Replies
    4
    Views
    6,058

    Re: F2-39

    Thanks for the info. I changed the thermistor and so far no repeat.

    Bill
  13. Replies
    5
    Views
    1,056

    Re: MX2310U random lines on copies

    I agree, memory causes a wide variety of strange output.
  14. Replies
    4
    Views
    2,192

    Re: mx-6200n f2-02 error

    the coupling rotates the bottle item 11 section 56 part no.ncpl-0084fczz. if this has fallen off the compression spring behind will be floating around in there somewhere.
  15. Replies
    4
    Views
    2,192

    Re: mx-6200n f2-02 error

    sounds like the coupling on bk2 has fallen off. remove bk2 and see if the coupling which rotates the bottle is still in place, you may be lucky and fit it back into place

    bill
  16. Replies
    3
    Views
    1,284

    HP hp3-c29 exam laserjet m4555

    Hello all

    the company I work for has asked a number of us to enrol with HP and take this exam. I have worked on HP equipment for 30 years and have never been asked to take an exam. Whrn I searched...
  17. Thread: F2-39

    by bonnie750
    Replies
    4
    Views
    6,058

    F2-39

    Hello

    I've got this code on a mx2700. The manual says it's the process thermistor which has a problem, connection/harness maybe. Is this the thermistor on the lsu?

    Thanks

    Bill
  18. Replies
    8
    Views
    1,066

    Re: mx 2700 lines

    i would go with memory too.

    Bill
  19. Replies
    2
    Views
    468

    mxm450 pin codes

    Hello

    Anyone out there got info on how to setup pin codes for copying on a mxm450?

    Is setup the same as the colour boxes?

    thanks

    Bill
  20. Replies
    3
    Views
    782

    Re: garbled cm 6040

    I fitted a jetdirect 620n card yesterday and we'll just have to wait and see. HP are trialling new firmware and they will post on Channel Services when they are satisfied it's fixed the problem.
    ...
  21. Replies
    3
    Views
    782

    garbled cm 6040

    Hello all

    I have an issue with a few cm6040s which produce garbled print randomly. The fault usually appears during a job not at the beginning and once started will produce the remainder of the...
  22. [Error Code] Re: MX-550N MFP showing up an error code f2-31 wont clear

    Why don't you call a tech and just get it fixed?
  23. Replies
    3
    Views
    596

    [Jamming] Re: MX6201 web seize

    Alan you'll have to put an all service bulletin out about this one!!!!

    Bill
  24. Thread: cm6040

    by bonnie750
    Replies
    0
    Views
    801

    cm6040

    Has anyone had a problem with skewed copies? Engine tests and printed documents are ok. copies off the glass and through the df are out by around 4mm on an a4r page.
    I reckon there must be something...
  25. Replies
    19
    Views
    8,246

    Re: MX4100 PPD2_PRI

    any fix on this?
Results 1 to 25 of 302
Page 1 of 13 1 2 3 4