I don't have PWS or altboot so reloading is not an option for now. At the moment I have an XEX-1 that stops at "enter current password" and a second XEX-1 with an ethernet port that won't connect. ...
Type: Posts; User: ac3243
I don't have PWS or altboot so reloading is not an option for now. At the moment I have an XEX-1 that stops at "enter current password" and a second XEX-1 with an ethernet port that won't connect. ...
Thanks for the reply. I already tried that.
Put a new CR2032 in and now it stops at a bios password prompt. I foolishly booted it with the cmos jumper moved and a USB keyboard attached to see if...
Help,
Had a XEX-1 that would not boot. When I attached a vga monitor, it was halted on cmos error. Looks to me like the CR2032 battery has died and CMOS can't be stored anymore. Is there any way...
I don't have a new parts book. I wonder what else has changed.
Hi,
Just installed a replacement ADF on a C552 and there have been some redesigns to the unit since the original was made. The part that concerns me is the hinges are different and the hinge stops...
You can use ghost, Acronis true image, or whatever hard disk imaging program you like. The fiery is not picky but Acronis True image has a better track record with techs that admit to cloning fiery...
First download the postscript drivers from Xerox. They are free.
Then follow the built in color calibration procedure in the printer. It may be enough without having to spend more money. The...
If you already have 2 PC's connected with a crossover cable, you can't connect the WCP 65. You have to use a hub or switch or router for more than 2 devices to be networked. If you have 2 Nics in 1...
I guess nobody has the edocs and altboot for the wcp45 anymore.
I'm still supporting M45's, WCP 35's, WCP 45's etc.. but I have had to buy print controllers when hard drives die. It's not quite...
I don't have the edoc files or altboot for my 9.2 PWS. Any help?
kerr@jimkerr.com
I lost my service manual for the WCP 35-45-55, M35-45-55, C35-45-55 series xerox copiers. Help
kerr@jimkerr.com
Do you still have any fk-103's for sale?
Replaced the HD. A 160Gb works and you get a bit over 120Gb reported as free space. A 120Gb yields about 98Gb free space. Both work and the fiery is back to normal.
That's not a very helpful reply. Since EFI is so free with download access and nobody is offering a contact at Konica-Minolta to apply for download access, it doesn't do much good to point out that...
It looks like I will have to buy another fiery and clone the drive to fix this one. I guess I can sell the extra fiery afterwards.
Please clarify: IP of each router, IP of Xerox WCP 65, IP of Dell computer, is it vonage or verizon(probably doesn't matter), how is it wired, do you have more than 1 dsl or internet connection....
Hello,
I've got an ic-401 with a dead hard drive and don't have the system disk to install a new HD.
The old HD is to far gone to clone and it's the only C350 with a fiery I service. Any help...
Cleaning manually worked. Could not see a thing on the LED arrays but came up with lots of toner on the cleaning cloths. I had cleaned them from the front but I must not have done much. Removing...
I cleaned the LED but can't see how Magenta and Black could be so badly effected but not Yellow and barly Cyan. Test prints look good except the final darkest patches where Black and Magenta look...
I have a customer with a C350 that's printing Magenta and Black very fuzzy and Cyan a little. I've attached a scan. At this point I've tried all I could think of in the service menus and I can't...
I've got several WCP 35,45's with the 1 line analog fax and that's a fax board with a CF card for storage that mounts in the copier body above the firewire board. It's not the right part number but...
What firmware versions can you load with a PWS. Since I don't have the network controller working right now, it's a little hard to tell what version it was running when it quite. If I start with a...
The one with the HD problem does not print a configuration report. The one I can clone works great.
I have a WCP 45 with HD problems. I don't have the files to install the software to a new HD. Can I just clone a working 3.98.50 drive from a working WCP 35? Is there a better firmware to put on?