Search:

Type: Posts; User: Sathsayin

Search: Search took 0.01 seconds.

  1. To be honest with you you said that it never...

    To be honest with you you said that it never happens when you have a crossover hooked up. Spits it out all day long. I think you could have looked over the fact(theres works for about a week are so)...
  2. Replies
    14
    Views
    2,630

    check the output from the hv board with your...

    check the output from the hv board with your meter. Like everyone else im leaning toward the the transfer roller. Alot of times the plastic tabs holding the roller in place will break from slamming...
  3. Replies
    4
    Views
    1,333

    You didn't say if you were using the doc feeder...

    You didn't say if you were using the doc feeder are the the scan glass. but if it prints fine then i assuming that that its with the optics. i would think that the doc feeder itself is not setting...
  4. Replies
    7
    Views
    4,554

    The toner waste bottle is locking into place.

    The toner waste bottle is locking into place.
  5. Replies
    7
    Views
    4,554

    5030 toner waste bottle problem

    The machine periodically comes up with a message to replace the toner waste bottle, but the bottle is no where near full. Installing a new toner waste bottle does not clear the message. The only way...
  6. Replies
    7
    Views
    1,437

    Sorry bout the late reply! had a bad day thats...

    Sorry bout the late reply! had a bad day thats the correct part number above! Didnt get a chance to log on at work today the internet was down .and when i got home had forgotten about it because the...
  7. Thread: SPAM posts

    by Sathsayin
    Replies
    4
    Views
    986

    took the words out of my mouth

    took the words out of my mouth
  8. Poll: kyocera, konica-minolta, copystar

    kyocera, konica-minolta, copystar
  9. Replies
    7
    Views
    1,437

    Ill get it for you at work tommorow. Do you need...

    Ill get it for you at work tommorow. Do you need the blade as well?
  10. Replies
    4
    Views
    3,727

    Hey thanks for the info kyoceradude. I took a...

    Hey thanks for the info kyoceradude. I took a look at the bullitin and will report to my boss tommorow . Somebody tossed the lsu out we had setting around are at least i can't find it. I'll see what...
  11. Replies
    4
    Views
    3,727

    km/cs 1620 lsu code reset

    first time working on a km/cs 1620 theres no 906? or equal i have c4000 code lsu/polygon motor. i unplugged and let sit for awhile then repluged back in and it comes up with 1 (copy output count) i...
  12. Replies
    18
    Views
    3,583

    Whenever you install the mk kits make sure there...

    Whenever you install the mk kits make sure there isnt excessive paper dust inside the drum area. charge can ionize the paper dust and conduct straight thru the drum. Technicaly the drum and charge...
  13. Replies
    4
    Views
    1,281

    Raym took the words out of my mouth. I would...

    Raym took the words out of my mouth. I would check to make sure the transfer has good connections also (when the transfer roller is in place. pull gently on either end at once to see if one end is...
  14. Replies
    4
    Views
    1,281

    I'm not sure if you checked your other reply are...

    I'm not sure if you checked your other reply are not. but the maintenance count will show you the count up to 150k but will not let you clear it once you reach 150k then it gives you the option to...
  15. Replies
    4
    Views
    1,575

    You cant clear the maintenance count on the drum...

    You cant clear the maintenance count on the drum unless it is above 150k.
    It will just show count. But will not have option untill 150 k is reached. called tech support on the same question before
  16. Replies
    8
    Views
    21,733

    thanks for the info as well blackcat4866 my...

    thanks for the info as well blackcat4866 my mistake
  17. Replies
    0
    Views
    817

    new km/cs 3050/4050/5050

    I noticed these new machines have linux on them. I know machines are expensive but i was thinking how easy a firmware hack would be. It would be funny for someone to hexedit some of the firmware. I...
  18. Replies
    8
    Views
    21,733

    well you cant really take the lsu apart you can...

    well you cant really take the lsu apart you can only replace it. i havent worked on that model but all lsu's work about the same. Maybe theres something i dont know but i thought you couldnt take it...
  19. Replies
    299
    Views
    581

    canada

    canada
  20. Replies
    8
    Views
    21,733

    does it make a loud whistleing noise. If so the...

    does it make a loud whistleing noise. If so the polygon motor may be going out. u may get 1 maybe 2 months. does the image looked warped are streched. could be dust in the laser bounceing around. The...
  21. Thread: Di 1610

    by Sathsayin
    Replies
    1
    Views
    1,255

    Di 1610

    Got a problem with a di 1610. Randomly pops up with paper size error after making copys sometimes you can make alot sometimes just a couple (customer says) she says it happens all the time but i...
Results 1 to 21 of 21