Search:

Type: Posts; User: glewisme

Page 1 of 10 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    4
    Views
    2,395

    [Dead] Re: Sharp MX2314N Hanging Screen

    I would try the SD card itself.
  2. Thread: Drum reset

    by glewisme
    Replies
    4
    Views
    903

    Re: Drum reset

    Thanks all. I'm a Sharp tech but they send me to anything!!! LOL
  3. Thread: Drum reset

    by glewisme
    Replies
    4
    Views
    903

    Drum reset

    I was wondering if someone would kindly share the drum counter reset procedure for the IR3320i ??
  4. Replies
    10
    Views
    5,482

    Re: Stuck Fax job in an MX-4101N

    66-10 seen this quite often!!!!!!!!!!
  5. Replies
    4
    Views
    1,621

    Re: MX-4111n - SPPD2_NM Jams using Bypass

    Have you cleaned the one way bearings and shafts in the bypass feed section???? Also in SIM 7-1 turn off mis-feed detect and try it. If it jams it's mechanical if not it's more than likely a sensor...
  6. Replies
    13
    Views
    8,176

    [Jamming] Re: Sharp MX-2640N SPPD3_N Sensor Jamming

    I.D.S
    Let me know how it worked out for you...
  7. Replies
    13
    Views
    8,176

    [Jamming] Re: Sharp MX-2640N SPPD3_N Sensor Jamming

    Actually access to the sensor is easy once the feed unit is removed. Flip it over and loosen the two anchor screws for the steel pf guide ( w/ white mylar) pivot it out of the way and there it is...
  8. Replies
    13
    Views
    8,176

    [Jamming] Re: Sharp MX-2640N SPPD3_N Sensor Jamming

    Removing the entire feed assembly isn't really too difficult. The top cover that houses all the sensors is the real problem. I get it to the point it's ready but there's just one spot that's hung up...
  9. Replies
    13
    Views
    8,176

    [Jamming] Re: Sharp MX-2640N SPPD3_N Sensor Jamming

    Has anyone torn one of theses down to be able to replace the SPPD3 sensor.??????? Doesn't look too fun at all.
  10. Re: Sharp MX 3501N has loud noise and dumping " Brown " waste toner.

    Blackcat is more than likely spot on. I've seen it many times. Waste toner coil gets bound by toner stones causing the drive gear to skip.
  11. Replies
    5
    Views
    1,360

    Re: MX-2640 loud vibration noise

    Mark happens to me all the time, 1 way to alleviate it is to set the web to advance after every job is completed I forgot sim but it does help out on the customers that just don't get it!!!!!
  12. Thread: Lift Gears

    by glewisme
    Replies
    3
    Views
    848

    Re: Lift Gears

    So I have discovered !!! That's OK we're getting the cassette under warranty!!!
  13. Thread: Lift Gears

    by glewisme
    Replies
    3
    Views
    848

    Lift Gears

    Hi all I have a FSC2626MFP the lift gears on the paper cassette has a couple of broken teeth .I cannot find the parts break down in the parts manual for the cassette only as a unit itself . I was...
  14. Replies
    4
    Views
    4,022

    Re: Mx-2314N Pdf files printing very slow

    Is your driver set to start printing immediately or to start printing after the entire job is spooled.?????
  15. Replies
    5
    Views
    1,237

    Re: Scan to Email Problems

    I do believe the newest firmware will allow you to enable SSL, so you can setup scan to email.
  16. Replies
    6
    Views
    5,094

    [Misc] Re: MX-2640 Fuser trouble

    I have one 2615 in the field that only does it after running a job with heavy paper without setting machine t heavy paper settings!! May try this though!!!
  17. Replies
    4
    Views
    1,862

    Re: MX4111N - Right door open

    Still cleaning up after others I see Mark!! LOL
  18. Replies
    0
    Views
    712

    MX2615N Noises

    Hey all, just wanted to let you all what I've found. I've had a customer call twice about loud noises when running envelopes and cover stock through the bypass. What I found is the customer failed to...
  19. Re: Sharp MX-2300N F1-10 Finisher Stapler Motor abnormality

    If I recall correctly it is the harness. Believe it or not as long as you remove the harness anchor points from the finisher it really isn't all that bad. Disconnect all connections and you can use...
  20. Replies
    15
    Views
    8,017

    Re: MX-5001 "cleaning transfer belt"

    Not sure if you fixed your issues but make sure the primary cleaning unit has no obstructions , or bound I have seen that cause what you're describing as well
  21. Replies
    8
    Views
    1,439

    [Misc] Re: opinion on mx-m453/503?

    You can also use. Part # CFRM-1425DS52 it the part # for the entire web assembly in the parts manual! Though they do cost more than the MX410WC
  22. Re: Need a new and better Spring Hook Tool for Coronas. Crawford tool one is bending

    If you like the Crawford tool ones you can use a propane torch and rapidly heat the hook then quickly cool the springhook in warm to hot water. This will greatly harden the metal, though it will make...
  23. Thread: mx-753

    by glewisme
    Replies
    6
    Views
    730

    [Jamming] Re: mx-753

    Turn off the jam detection in sim 7-1 if it passes paper fine you know it's a sensor issue. More than likely the PPD1 sensor in the PS unit is dirty or failed if it stops at the registration roller
  24. Thread: Marijuana

    by glewisme
    Replies
    44
    Views
    4,627

    Poll: Re: Marijuana

    Think of the drop in crime especially in the southwest if Mary J was legalized. What Mexican cartels. Hell everyone would have a basement grow lab!
  25. Thread: Marijuana

    by glewisme
    Replies
    44
    Views
    4,627

    Poll: Re: Marijuana

    I don't partake in it unless totally wrecked ( drunk) but I have no issues with it. I would if the smell didn't bother me. Truth is I think it's harmless!
Results 1 to 25 of 241
Page 1 of 10 1 2 3 4