Search:

What mechanism?

U just show it in right?

Does the replacement have bronze bushings? Or do you need to replace the new assy again in future?

I just pull the magnetic wheel from the motor en clean the 2 white plastic disks, with alcohol and a piece of paper. Make sure they don;t stick to much, the magnetic disk needs to slip allot when the...

You changed the cleaning blade right? Still not cleaning the itb. I believe that your ITB not properly aligned inside the machine. Remove the ITB and check inside the machine if the 2 hooks that...

Replace the M Laser, the power control goes bad. This laser is becoming much to intense.

If you don;t believe me, swap with another color en see another drum and toner get screwed. I replaced...

The 5035 is cheaper in running costs.

U replace drums instead of IRC5185 drum units.
ITB last longer 600k instead of IRC4185 300K
And the Fixing, after 400/500K u need to replace the fixing...

Here smoking in the office is not allowed anymore. Still we need to clean/replace those corrona;s much to often. Piece of shit, Advanced my ass. Beter find an older refurbished 5570, much beter, it's...

Most of Europe is 230V these days. Equipment here should be able to work at 240, it's less than 105%.

Only older equipment is built for 220V, sometimes they start buzzin at 230

Does it light up and move the mirror? Of not, there is no power in the reader unit.

Check the card in the main controller box to which the reader connects to, clean the connectors of all the cards...

It's a problem with yer Primary Charging voltage of Magenta. Maybe a bad connectoin, caused by the move.

Reseat HVT1 and HVT2. They are in the back and you need to remove the main controller box,...

E0012 actually, becoz the Cyan feed screw jammed the drum motor, it could not push out the waste toner into the main feed screw in the back.

http://i50.tinypic.com/14o7gy0.jpg

http://i48.tinypic.com/xdz57b.jpg

http://i46.tinypic.com/11ieo8x.jpg

http://i48.tinypic.com/27ysmzp.jpg

http://i47.tinypic.com/2d9zpds.jpg

A real "technician" can easily refurbish this printer by himself. Cheaper en just as much work, than shipping a big lump of fuser assy. Whats next, replacing the AP kit?

Our 58 and 68 series machines that are still running are now up to 1,5M copies. We never turn the drumphase, never seen any trace of drum memory.

Black drums don't leak as much on a C3220, not like the 4080 does. And black looks good on the examples.

Try to replace the color drums, they are gone.

What is the humidity?

Try removing the transfer rollers and moisten them. If it works its temporary though.

So in short, Sharescan would run on a Develop machine. But eCopy does not allow it?

Particularly Ecopy, Autostore and Safecom?

Since they are basicly copies of the Bizhub line, i wonder of they support embedded solutions built for Konica Minolta machines. Or am i missing...

Image Transfer Belt

So it is either an ITB, ITB unit or ITB assy, or u can call it "the belt" of yer machine has no other belts, like separation or fixing belts.

ITB Belt would have the word...

How is the primary corrona? How is Tp3 with po-cnt disabled?

Would that new firmware help scanning to OSX 10.7 and 10.8?

This my weapon of choice:

http://www.brigatti.nl/contents/media/cable_tie.jpg

But i don;t see how this would help repairing the flag, i had those in stock, otherwise swap it with the no4...

If this is a IRC2880 or like, u can start by cleaning the laser windows by hand. Since they are underneath they tend to collect dust.

Inspect your drum very thorough for marks or a small dot of toner. Here we got allot of problems with dots/contamination on the drum surface, these dots damage the cleaning blade so it starts to give...

U need to clean/refurbish your ITB. Pull out the right side drawer, remove the cover above it. Open the front cover, lower to blue handle. Now u can slide out your itb unit.
...