Hey Thanks Rorschach . Very good trouble shooting skills on your part.
Replaced corona assembly
No 24vdc
Replaced PSU3
No 24vdc
Will look at the harness
Also, thinking way outside of the...
Type: Posts; User: Livebychance
Hey Thanks Rorschach . Very good trouble shooting skills on your part.
Replaced corona assembly
No 24vdc
Replaced PSU3
No 24vdc
Will look at the harness
Also, thinking way outside of the...
Thanks for the response.
We swapped the entire assembly with another color. Sensor motor off another color still same SC code
We rebooted the machine with the doors open and as soon as we...
Printer only version C9110 SC 590-01 will not go away.
Things we have tried:
Swapped assemblies with another color
Turned off in Sp mode rebooted
2-220-001 O no operation
Jam code 72.16
Also, all firmware updated.
Riddle me this Batman.
C6500 runs all day face up or face down.
Jams duplex. Easy right? not so fast.
Remove finisher (FS-607) runs all day, duplex, face up, and face down.
Finisher main...
Still no worky. 3901 was able to get machine to work but still error message is displayed.
Forgot to mention under 200 prints on machine.
New controller same thing.
Thank you, will look into that later today.
I have a Ricoh C811dn that says, “Turn main power off, then set PCU correctly Black, Cyan, Magenta, Yellow”.
Tried new PCU’s
Flashed machine to latest and greatest
Re-set PCU’s in service 7804...
Our versions do not coincide because the rips we sell are dumbed down.
Mechanically exact same rip.
Here is the part number on the rip I believe should translate to your IC408,
45057792
My terminology might be different (not sold as Konica). We do not call it a ic408.
Here is our firmware history with the internal rip (hangs on back).
1.0
1.02
2.0
Also, my versions are...
How far apart are the jitter lines?
We have tried different rip cables, swapping cables around, firmware 1.2 to 2.0 back to 1.2., o no avail. We currently have had four rips that would reverse image , totally black, and all sorts of...
Have the mylars been removed from the FS-607?
We have had many occurrences of this, It’s definitely the Fiery but we returned them.
If i were to guess it would be the video board of the rip.
Let’s say job A causes a problem and job B does not.
Can you run job A at anytime (a week later) and have a problem?
Does job A have allot of saturation?
Can job A and B swap problems?
...
The spectrometer has done wonders for our Konica output. Yes, even removed magenta hue.
Thanks random, did not think to check power save in XP.
IC-408
Image cut off in many different applications with files >300meg
Does not happen all the time, does not cut off image in same spot....
We have a boat load of 8050, 500, 5500, and 6500’s out in the field. I mention these four models because they are basically the same machine improvements on each generation.
With that being said...
We have had good expirence with the 601's as well.
Weight plates were added to some for feeding thick gloss paper.
remove mylars as the paper travels down plate, four in total.
607 has mylars (550,650 stapler finisher)
606 does not (500)
215 does not (8050)
twinax, what is the complete configuration?
Laserman06,
Sounds like you have it covered but, it would not hurt if you haven't already done so, to do a forced auto color registration.
36 mode
Timing adjust
Auto Color Registration
How many clicks since last PM?
These codes may be indicative to stretching PM parts and developer.
Joxandro, does the machine have a LCT?
If it does, try your adjustment out of another tray.
The LCT has a skew sensor which has caused unusually problems in the past.
replace ADU board.