Search:

Type: Posts; User: certifiedxeroxtech

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    4,682

    Re: MP C2503

    Thanks for the responses. Actually I did replaced Yellow PCU housing only. Due to some budget issue. I'll update you sooner for the outcome. regards.
  2. Replies
    10
    Views
    4,682

    MP C2503

    Anybody experienced these? Yellow or Magenta toner emptying so fast and it goes all to waste bottle? please need solution on how to prevent this to happen again. Do I have to replace the PCU of 45k...
  3. Replies
    8
    Views
    2,782

    Re: Toner Empty- MP C2503

    dears, I've replace two sub-hoppers. It went snapped all of those. I repaired the 2nd hopper using a soldering iron and I decided to update firmware. Anyways. It was solved already. here's what I've...
  4. Replies
    8
    Views
    2,782

    Re: Toner Empty- MP C2503

    thanks for the responses. DV and PCU replaced but still toner get stocked on the opening.
    No gears defective. DV clutch ok.
    Why I had to suspect the firmware? because I am guessing, sensor on dv...
  5. Replies
    8
    Views
    2,782

    Toner Empty- MP C2503

    I'm having an issue of toner depletion inside the Development unit of MP C2503. I began to force toner supply and the spiral gear inside the sub hopper gets twisted and been cut on its shaft due to...
  6. Replies
    5
    Views
    818

    Re: GESTETNER DSM745

    Did you clean the toner recycling unit in the drum section of the machine? Paper dust blocks the opening in the toner recycling unit.
  7. [Misc] Re: SMTP Rejected my Scanned files from a MP C2550

    Already did. Thanks to you. I'll update this thread sooner or later.
  8. [Misc] SMTP Rejected my Scanned files from a MP C2550

    #[dcs_nas(74)]13/08/19 15:37:41 SMTPC: received error code. [501] (202) ERR:
    #[dcs_nas(74)]13/08/19 15:37:41 SMTPC: connection closed. (801) ERR:
    #[dcs_nas(74)]13/08/19 15:42:27 SMTPC: received...
  9. Replies
    13
    Views
    6,170

    Re: Another SC 670 for MP C2550

    Dear All, this case is closed. Power Supply issue.
  10. Replies
    13
    Views
    6,170

    Re: Another SC 670 for MP C2550

    andy227 haha! I am freakin' feelin' bad about issues like these. So I decided to put on some heavy thing while working. We currently order NV ram thing as per experience for these models and...
  11. Replies
    13
    Views
    6,170

    Another SC 670 for MP C2550

    We are experiencing this error a week ago and still not solve even we change the Controller board and BICU board. Anybody here can give us support. Thanks.
  12. [CQ] Re: IR5055 dark copies on Insterts and covers only

    Try to figure out the paper size settings. is it A4 or letter size?
  13. [CQ] Re: IR5055 dark copies on Insterts and covers only

    where did you load the inserts/ slip sheets, could you show us samples?
  14. [Electrical] Re: Ricoh 551 toner bottle motor not spin

    vaccum the tubes and clean the development unit first,
  15. Re: IR 2200i horizontal lines on print (especially at start of page)

    dont freak yourself change the drum. It is grounded. clean also the development cylinder and adjust the doctor blade.
  16. Replies
    16
    Views
    2,088

    Re: PRINT QUALITY

    check the toner save mode.
  17. Re: Problem with MP9000. Please urgent help

    align the web padre or check the whole fusing unit.
  18. Replies
    6
    Views
    7,949

    [Error Code] Re: SC-551 on Nashuatec MP C2550

    so far, the best possible way i did is plug the unit to AVR...Thanks folks
    of course i replaced all the thermistors and thermostat twice in a month...
  19. [Error Code] Re: What is the Meaning of SC863 Error appears in Nashatic dsm627 Copier machine Plea

    Next time you have to make sure of the power fluctuations to be controlled to prevent that damage on your machine. Use AVR 2000watts or higher.
  20. Replies
    6
    Views
    7,949

    [Error Code] SC-551 on Nashuatec MP C2550

    Please share the best solutions as the error keeps coming back.
  21. Replies
    15
    Views
    3,569

    Re: printer configuration (MP 2000LN2)

    hah! maybe if you install the optional trays you'll get the proper configurations. And or check the destination settings go to 5807-01 check the values.
  22. Replies
    4
    Views
    1,759

    Re: H2-00 (AR-5127)

    You have to reset fuser errors with simulation 14. Press P * C * then 14 then Start. If not then replace the fuser.
    SM 5-1 should turn the lamp on. If lamp blinks on and off it is the thermistor,...
  23. Replies
    8
    Views
    1,291

    D0091498 do you think it is compatible? from...

    D0091498 do you think it is compatible? from Nashuatec catalog
  24. Replies
    13
    Views
    3,753

    replace the controller board...We experienced it...

    replace the controller board...We experienced it here in Saudi...improper shutdowns etc. is the main cause
  25. Replies
    8
    Views
    1,291

    what happen to touch screen?

    what happen to touch screen?
Results 1 to 25 of 27
Page 1 of 2 1 2