I have the manuals. I have been working on these for years. Just need some thoughts on things to try. Thanks anyway
Type: Posts; User: laserman06
I have the manuals. I have been working on these for years. Just need some thoughts on things to try. Thanks anyway
I am having an issue with a C6500 with an error code of c-3903, or high temp abnormality. It will reset and start to warm up and faults out within 30 seconds. We have swapped out the fuser unit and...
How did you calibrate it? I have found that the best way to calibrate it is with a spectrometer. When you do it off the glass, make sure all optics and mirrors are clean. I have found that the...
I have a KM c652DS with a C3B02. We have replaced the fusing unit, IHPU, PRCB and REDB and coil unit. Checked the operation of the upper right door. All checks good. Any suggestions?:mad:
Have a brand new KM652 with a C-6104 code. Any suggestions? I am asking for a friend of mine.
Clean all of the slit glasses on the write units.
Reseat connectors on the image process board.
Provide pictures of defect if possible.
My favorites:
1. You first arrive, before you look at machine...What is wrong with it and how long will it take?
2. You have the machine tore apart and some idiot asks.....Can I make a copy?
I have a 6135 that is throwing a P04-210 code. We have swapped out MIN and PHN core boards and speed sensor . Replaced the PR roller cable. Problem went away for about 150 12-page books. Now it will...
I would pull out the drum carriage and clean the connector on the back of the machine and drum carriage. I have seen many codes caused be that. Also, you might have a bad set of drums. Did this start...
I have a KM 1050 that runs fine out of tray 1 until just a few sheets left in the tray. Clear jam and reload paper runs fine until few sheets left again. Any suggestions? Over 2 hour drive to account.
I have several c5500 and have stretched the maintenance counts to the same as c6500, no issues. I was told many moons ago, during class that it is due to the slower speed. It takes longer to get to...
I would say RUN! My company tried them and I would say that we had a 80%-85% failure rate. I was introduced to some weird print issues with them.
Just sent you a PM.
Couple of things...1. When using coated paper, the machine should be set to coated. 2. I would have your tech perform the transfer belt and fuser belt speed line adj.
Not necessarily, look at your boot up process in the theory manual. If I have seen the exact same problem on another machine. Installed a line monitor and within 24hours we had over 4000 hits....
Firmware is very important. I too have fixed many problems by upgrading/reflashing firmware. Why are some people so afraid of FW? They put out updated FW to correct many issues. So, when it comes to...
Before I reset the IUs or the transfer belts, I always print out a 11X17 halftone test prints in each color. If there are any defects, I replace them. If you only have defect in one color, replace...
Look at this thread. There are others also.
http://www.copytechnet.com/forums/konica-minolta/10438-replace-transfer-belt-unit-bizhub-c351-2.html
Just like I do sometimes!:D
Could have been something as simple as a power surge/dirty power. Have seen many issues with KM boxes and power issues.
I resolve to not make any resolutions:p
Can we all just get along?:D
I got a 22" flat screen monitor for my desktop, a new laptop, a TomTom One.
My wife said she got me the TomTom because she was tired of telling me where to go. :p What do you think she...
This is exactly right. I have a c6500 that is in a print shop. I have to replace the belt about every 150K. He uses large and thick stock. It only counts 1 click per large paper for total counter and...