Search:

Type: Posts; User: laserman06

Page 1 of 14 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    5
    Views
    14,403

    [Error Code] Re: Konica Minolta C6500 Error Code c-3903

    I have the manuals. I have been working on these for years. Just need some thoughts on things to try. Thanks anyway
  2. Replies
    5
    Views
    14,403

    [Error Code] Konica Minolta C6500 Error Code c-3903

    I am having an issue with a C6500 with an error code of c-3903, or high temp abnormality. It will reset and start to warm up and faults out within 30 seconds. We have swapped out the fuser unit and...
  3. Replies
    3
    Views
    518

    [CQ] Re: Biz hub c500 with too much blue

    How did you calibrate it? I have found that the best way to calibrate it is with a spectrometer. When you do it off the glass, make sure all optics and mirrors are clean. I have found that the...
  4. Replies
    3
    Views
    1,715

    [Error Code] C652DS with C3B02: IH malfunction (CPU)

    I have a KM c652DS with a C3B02. We have replaced the fusing unit, IHPU, PRCB and REDB and coil unit. Checked the operation of the upper right door. All checks good. Any suggestions?:mad:
  5. Replies
    16
    Views
    19,908

    KMC652 Error code C-6104 code.

    Have a brand new KM652 with a C-6104 code. Any suggestions? I am asking for a friend of mine.
  6. Thread: C 500 PRO

    by laserman06
    Replies
    8
    Views
    853

    Re: C 500 PRO

    Clean all of the slit glasses on the write units.

    Reseat connectors on the image process board.

    Provide pictures of defect if possible.
  7. Re: I need your expert advice: Ricoh MP C6501 SPF vs Konica Minolta Bizhub C-552

    Bizhub c552
  8. Re: Out of this world questions of the costumers.

    My favorites:

    1. You first arrive, before you look at machine...What is wrong with it and how long will it take?

    2. You have the machine tore apart and some idiot asks.....Can I make a copy?
  9. Replies
    0
    Views
    638

    [Error Code] P04-410 on 6135

    I have a 6135 that is throwing a P04-210 code. We have swapped out MIN and PHN core boards and speed sensor . Replaced the PR roller cable. Problem went away for about 150 12-page books. Now it will...
  10. Replies
    1
    Views
    5,764

    [Error Code] I would pull out the drum carriage and clean the...

    I would pull out the drum carriage and clean the connector on the back of the machine and drum carriage. I have seen many codes caused be that. Also, you might have a bad set of drums. Did this start...
  11. [Jamming] 1050 jams with few sheets left in tray 1

    I have a KM 1050 that runs fine out of tray 1 until just a few sheets left in the tray. Clear jam and reload paper runs fine until few sheets left again. Any suggestions? Over 2 hour drive to account.
  12. Replies
    9
    Views
    2,072

    I have several c5500 and have stretched the...

    I have several c5500 and have stretched the maintenance counts to the same as c6500, no issues. I was told many moons ago, during class that it is due to the slower speed. It takes longer to get to...
  13. Replies
    6
    Views
    1,369

    I would say RUN! My company tried them and I...

    I would say RUN! My company tried them and I would say that we had a 80%-85% failure rate. I was introduced to some weird print issues with them.
  14. Replies
    6
    Views
    1,235

    Just sent you a PM.

    Just sent you a PM.
  15. Replies
    16
    Views
    3,697

    Couple of things...1. When using coated paper,...

    Couple of things...1. When using coated paper, the machine should be set to coated. 2. I would have your tech perform the transfer belt and fuser belt speed line adj.
  16. Replies
    6
    Views
    1,726

    Not necessarily, look at your boot up process in...

    Not necessarily, look at your boot up process in the theory manual. If I have seen the exact same problem on another machine. Installed a line monitor and within 24hours we had over 4000 hits....
  17. Replies
    34
    Views
    18,309

    Firmware is very important. I too have fixed many...

    Firmware is very important. I too have fixed many problems by upgrading/reflashing firmware. Why are some people so afraid of FW? They put out updated FW to correct many issues. So, when it comes to...
  18. Thread: KONICA C350

    by laserman06
    Replies
    4
    Views
    1,207

    Before I reset the IUs or the transfer belts, I...

    Before I reset the IUs or the transfer belts, I always print out a 11X17 halftone test prints in each color. If there are any defects, I replace them. If you only have defect in one color, replace...
  19. Replies
    1
    Views
    1,141

    Look at this thread. There are others also. ...

    Look at this thread. There are others also.


    http://www.copytechnet.com/forums/konica-minolta/10438-replace-transfer-belt-unit-bizhub-c351-2.html
  20. Replies
    7
    Views
    9,630

    Just like I do sometimes!:D

    Just like I do sometimes!:D
  21. Replies
    9
    Views
    6,119

    Could have been something as simple as a power...

    Could have been something as simple as a power surge/dirty power. Have seen many issues with KM boxes and power issues.
  22. Replies
    13
    Views
    1,477

    I resolve to not make any resolutions:p

    I resolve to not make any resolutions:p
  23. Can we all just get along?:D

    Can we all just get along?:D
  24. Replies
    32
    Views
    3,353

    I got a 22" flat screen monitor for my desktop, a...

    I got a 22" flat screen monitor for my desktop, a new laptop, a TomTom One.

    My wife said she got me the TomTom because she was tired of telling me where to go. :p What do you think she...
  25. This is exactly right. I have a c6500 that is in...

    This is exactly right. I have a c6500 that is in a print shop. I have to replace the belt about every 150K. He uses large and thick stock. It only counts 1 click per large paper for total counter and...
Results 1 to 25 of 329
Page 1 of 14 1 2 3 4