hi
this probleme occure in copy mode ?
in print mode ?
in scan mode ?
Type: Posts; User: RICOHTEC
hi
this probleme occure in copy mode ?
in print mode ?
in scan mode ?
HI
I have one jam for 100 copy done.
it's a jam with no paper feed.
paper feed ASSY was changed and tray lift motor.
thanks for you help
Creating the PDF:
1. Open a document and select "Print".
2. Click the PDF button and then select "Save as PDF...". Save the PDF to any location.
[Symptom]
SC491 (High-voltage: Charge/Development: Output error) is displayed.
[Cause]
Drum (PCU + Dev. U) development unit is faulty.
[Resolution]
Replace appropriate drum unit.
thanks for your answer. But a don't when error codes but a want a document whichexplains how to analyse a protocol dump T30 .
HI
i have a problme with an MPC2800.When a try to send a faxe the communication is broken after a few moment . I print the protocol dump But i could not analyse the informations .
So I am in...
I have find the problem
It was a problem in the Harness BICU ---------> SBU
HI
I have an aficio AF3260c that make sometimes at start up .
home position sensor , SIOB and optique motor have been change .
We change also SBU .
thanks for your assistant and grieved...
Very good info . I also use many time clear RAM ENGINE to solve pb end toner detection.
but after clear RAM you must change all developpers.
HI
it's a probleme with toner chip set on toner cartridge.
Change toner cartrige and force toner supply , but somtimes you must change also dev unit
HI
Look for SP 5811 002 DISPLAY SERIAL NUMBER AND SP811 004 BICU SERIAL NUMBER
SC995 002 = DEFECTIVE NVRAM
SC 220 Laser Synchronization Detection error
[Cause]
Defective SBU
OR
DOOR SWITCH
[Resolution]
Replaced SBU which is part of the Lens Unit B247 1721
OR DOOR SWITCH
hi
to have a good value for the amount of toner in the cartridge make an ENGINE clear RAM and then change your developpers.
hi
i change the DTMB and the probleme desapear
hi
i have an MPC7501 witch made an SC625 .
PSU and VBSU have been change and a steal have the same probleme
Some one have an idea
(sorry for my english)
HI
it was a probleme with VBCU assy
The machine is clean and all dev are changed .
hi
i have a similar probleme and it was a probleme with one of the two memory card on controler
HI
I have a that make SC446 .
I have a photocopier MPc6501 which makes me a code sc446 intermittant.
I changed the sensor position CTI ( AW010045).It's not due to toner projection. ...
Look for broken spring on paper feed assy
or
you can also adjust the position off right tray in the machine (look at the back of right tray for adjustement)
Symptom]
SC376 (ST sensor minimum output error: C) is displayed and the set development unit (cyan) indicator is displayed in the upper left part of the screen.
[Details]
The power was turned off...
A. Damaged wiring harness between IPU and BCU PCB. Pin 2 (LD Monitor signal) of the IPU side of the harness which plugs into CN 347 becomes damaged from improper opening and closing of the...
hi
I have a probleme with detection paper on right tray in Tandem
PCB Paper board was change
(when a put the tandem in the machine i don't here the activation off pick up sol)
need...
SC 350, SC 352 or SC 390 codes and/or light copies.
https://eu-tier2-en.custhelp.com/rnt/rnw/img/trnsp.gif
SC900DElectrical total counter errorGW The total counter contains data that is not a number.
NVRAM incorrect type
NVRAM defective or corrupted
Unexpected error from external source