Problem solved by myself.
Type: Posts; User: mdm7266
Problem solved by myself.
IR 2530 scanning lamp does not light upon scanning. even at power on start up or initialize at power on does not turn on. Already replaced scan flex cable still the same problem.
no error code....
I know the part number of the carriage assembly.
Its FM3-9435-000 Carriage unit
I would like to know if i can order the CCD unit only if it has its separate part number.
I dont have the...
Hello all, Can somebody give me thd part number of the CCD unit Only. Not the Scanner assembly. Only the CCD.
E248 001
All SCAN > READER> FUNCTION > CCD > DF-WLVL1/2/3/4
NG status
Upon engine error clearing E719 occurs. erroneous communication on new card reader. But did not replace card reader.
Hello teckat. Error 248 return again. This time it wont clear the error in service mode. Also tried rcon clear. Still error 248. stdr-pos NG. Do this error can be solve by reflashing? Can this be...
Check, clean and reinstall the flex cable going to the scanner/reader assembly. Clear error solved the problem error 248.
Thanks for the reply Teckat.
Hello. I have a problem on ir2545. I already replaced the flex cables, relay controller, main controller, dc controller and the power supply and still error 248 upon power on. The error does not...
This is what happen. Ir2545
At first its intermittent error 248. at first error is cleared by power off-on. then suddenly at power on the machine cannot start-up or boot. the green light on the...
hello. can you please give me a copy of ust firmware or the tools needed for my ir2545. my ir2545 cannot start/boot. cannot enter service mode. i will try to reprogram.
How did you solved the problem? what did you do?
where is the tcp/ip cable located?
3716437165Can anyone please send me the procedure on how to remove finisher canon IR 2530?
I saw a plastic part of the machine up the output roller falling down thus blocking the movement when the...
Check the spring of the solenoid at the back of the bypass tray. the spring of the solenoid do not return to the proper position. (you need to change the spring with enough strength to pull the...
at power on still jam indication pointing at middle right door. cannot even make a single copy because at power on indicate jam.
Here is the jam code
B_JAM0: 0208 010A 010A
B_JAM3: 010A 010A 010C
B_JAM6: 010C 010D 010C
B_ALRM: 0001
Replaced wiring from dc controller
Replaced pick-up assembly
replaced unit 1 assembly
Problem "jam at right door remove jam" its pointing on the middle door.
Replaced ps30, ps27, ps36 still jam at power on.
Do pick-up assembly can cause jam indication at power-on on the copier? it...
i tried your suggestion but the same " open right door remove jam paper" the machine is pointing a jam at the middle right door.
jam at power on. i tried the reset *4* same problem
Here is the...
i have the same problem of false paper jam. no paper but indicate jam at lower door. replaced vertical path sensors ps27, ps 36, ps 30 all good.
look for the recent jams the screen displays all...
i found the answer to my problem on error 031. I replaced the main power switch. It is the small coil on the middle of the power switch causing error 031.
error 031 is gone but the machine...
already checked and clean contacts of front door switch. i also use tester to check continuity. ok. problem still 031.
Replaced DC power supply assembly. problem still error 031 . i'll check the front door switch.
For more info. Replaced DC controller, Option counter and total counter.
Error 031 at power on still exist.
hello. my problem is the shade (not dirt) about 2" on the leading edge at the back of output paper.
attached is the sample (back of the copy paper) i jammed the paper and found out that the...
Hello there. hope somebody will share their technical expertise on my problem. First of all i will tell you that i have no other machine at the store. only 1 canon np 6050 that's why i have no chance...