That is exactly what it was. Ended up parts cannoning it and eventually got to the motor (last thing I tried).
Type: Posts; User: Jake2o
That is exactly what it was. Ended up parts cannoning it and eventually got to the motor (last thing I tried).
I have an SD-510 installed in an FS-532 and whenever it is connected I get a "close finisher door" message on the engine. I have taken the SD-510 out and installed it in another FS-532 and the...
I have 2 in a major user that staples everything. They seems to need them replacing every million or so impressions; It just falls off so they keep telling me. Trouble is that it is civil service...
Haha; I know what you mean.
For anyone looking at this thread for inspiration I have now found the part number which is
A4F3R71511
Hi all,53826
I wonder if anyone knows the part number for the kit to repair the stacker when the stopper breaks off.
21 A4F3727300 Slide Part /Lower;
22 A4F3729100 Regulating Plate /2;
23...
I have a 1052 in a customer that is going through developer every 80K, for some reason it is just disappearing from the housing. I have now just changed the housing, but am not convinced it will...
I have taken the whole fuser assembly (belt unit, roller and frame), and whole drive unit out of another machine and it still does it; I have changed the decurler too. The only time it errors is...
I am working on a 2100 with a This is a fuser motor over current error; Changed the motor and the whole fuser from a known working machine but it made no difference. initialised NVM's, reinstalled...
Well that was unfortunate; For anyone reading this thread if the upper fan gets stuck on DCPS1 then it will result in the machine asking you to close the front doors. Obviously the load of the fan...
I have a 1052 that I took the screen harness out of to repair another machine on site; Now I have come to put a new harness in this one I have reassembled it and it is saying "Please close the front...
Thank you for pointing me in, hopefully, the right direction. It threw me because it was out on side 2 rather than side one so I did not even consider the edge detection sensor in the LU-202 or its...
These things are a bit before my time, but I have been landed with one and need to sort it. It has an odd issue with registration on side two in that it will randomly move the registration about...
Thanks for that. I'm currently talking to Milo so I got that one right. The iGen was sold by a 3rd party into Africa and we were only asked to install it because it had been refurbished and only had...
Can anybody get me licenses for the iGen4?
How are you at sorting out the numerous Licenses for the iGen 4
How are you getting on with this?
iGen yes
Has anyone had any dealings with a company in Canada called "Recharge Store"? We tried to purchase a resetter and 2 modules for writing Xerox chips along with a couple of what they call "cdf" files...
Hi all, I am looking for a process unit frame/carrier for a C5500/C6500. Just the metal frame, I don't need the dev's or the drums; preferably in the UK.
Thanks.
So I tested the Erase lamp circuit and checked it in state confirmation and it operates exactly as it should which leaves me absolutely clueless as to what is wrong with this carrier. I have now...
Ahhhh! you might have hit on it there, I just never thought of that for some reason. The lamp is wiping it as fast as the grid is charging it, that would make perfect sense; will give it a go...
It is probably the grid grounding, but I just do not know what on.
If I send test pattern 11(beam check) then I can definitely see the pattern under the black is as it should be. I can't do a...
So I have this 6500 that is printing black sheets indicative some sort of failure of the charge corona being able to charge the drum; simple enough under normal circumstances, but this is the...
Magenta ROS; try reseating cable (PS. if you have not done this before then get an engineer, they are very awkward to install correctly).
2 favourites are the drive for the duplex belt has become worn or, if it is not picking up from the lower paper trays a cog has slightly slipped because it has a crack in it. and annoyingly it is...