Search:

Toshiba 4511 with MJ-1024
When trying to clear saddle stitch staple jams or replace saddle staples the unit does not preform the staple test when the saddle stitch is returned to the closed position...

The dots don't appear on black and white, only on color. If the drum was damaged it would be on all prints. It's as if the printer is printing some sort of test pattern that doesn't get wiped off....

Toshiba 351C on color prints or color copies appear KCMY dot pattern as shown in attached photo. They are always aligned back to front on the page but appear in random locations right to left on the...

Any one have the replacement part number for 6LA29934000? My supplier said it has been discontinued.

Anyone close to Northern NJ that has a 2nd transfer roller for a 351C or know of a parts place open on Saturday? This one is coming off it's roller during a big print job that needs to be done...

Getting CEB0 on one of the 3511 as many other have.

From what I gather online the CEB0 is related to upgrading the black dev clutch clutch motor. The motor does function and the dev lift sensors ...

I'm thinking it is something on the carrier as I just replaced the lamp and three copies were fine at 65% Switched to 50% and heard a clack and the image was back. Went back to 65% and the image is...

Once again I come forth with a question about the nightmare 3511, but lets see if anyone has seen this before.

When copying at 65% or lower (I imagine) the corner of the print has a nice black...

Is there a kit for the seals on the black developer unit. I see individuals 6LA29869000 6LA29870000 & 6LA29921000 I'm also in need of the filler square that seems to dry rot on most of the...

How do I handle the PM and other counters being off now? 08-999 didn't look like it did anything except transfer the total count to the 999 bank. Do I do the nvram to sram transfer or will these...

I need to replace the sys board in a 3511 is there a procedure that needs to be done in 08 mode when the physical swap is done. All I remember is 08-995.

3511/4511

After any B&W copy the unit goes into WAIT for a few seconds after copying.
When something is printed to the unit there is no WAIT after the print comes out.

What is the extra steps...

In need of 6LA31910000 GEAR-5H43-6


Can't find them on the net, is there a good source for these odd ball parts.
Anyone have a couple laying in the truck?

White tube around IH Coil has some creases in it, can't locate part number. Keep, discard, replace?

Just learning the Canon 3200 series. What are the differences between the 3220 3220G and 3220N. A quick search only shows the G as a government version, is this accurate? Does that mean the G version...

I have a 3511 that has gone through three developer motors in the past year. Never had this problem and any other 4511/3511's so I don't know what's causing it. Somehow the shaft gear on the motor...

Toshiba 4511 w/ MJ1024 Can we change the saddle stitch maximum page count over 15?

Level 1

Settings 0: The external controller icon is displayed on the control panel of
the copier
[Factory default/After RAM clear]
(When the color image server is connected.)
1: The control...

I learn by doing and figuring things out on my own. I do have the SM. I found the setting by switching items on and off. But thank you very much for your suggestions.

Option / Body / CNTR-DSP = 1

Hi, I am now learning the C 3200 & c3220, my first two Canon copiers in my collecting (I have 3 toshiba 4511 yuck)

Print Tab on the c3320 is not longer there after playing in service mode, I must...

Is there a way to get this set up to fold two sheets that come from two different draws without stapling them?
I have the print driver set up to print an invoice from the top draw and print an...

Never mind, I found the solution on my own. In case anyone needs to know, go to start menu/control panel/printers right click toshiba/run as administrator/properties you can then change the...

I just installed the ps3 driver on a vista box and noticed all the option in the configuration are greyed out as well as the fonts window is this normal for the Vista driver for the 3511/4511 or am I...

Yes Spock, this is exactly the type of adjustment I was looking for. Except I can not find anything like what you describe.

I am in the lower jam access door, directly under the trays. When the...

Your talking about the inner side plate assembly correct? How exactly is it supposed to get adjusted? Not like any of my tools would go in there easily to do so )o:

I tried just adjusting the...