Search:

Type: Posts; User: Itsthepaper

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    13,475

    Re: Fiery IC415 on C1060 controller disconnect

    Just had the same problem last week. Installed latest system software version. 2 and new hard drive and all has been well.
  2. Hp Design Jet T920 does not form cut in between print jobs.

    When roll runs out during print job, I don't seem to find a way to perform a clean cut on lead edge of the new roll.
  3. Bizhub 754e...doesn't multitask when hooked up to 3rd party solutions software.

    Need some help testing an issue, Bizhub 754E while its processing a print job mainly a big job if you go into scan mode the machine has a message that says "know scanning or know copying". While this...
  4. [Annoying] Konica Minolta C1060, little dissapionted over here.

    We put a out a new C1060 and it's been a little tricky to say the least.

    1. Right out the box the SOB jams on plain letter paper with full coverage every time.

    2. Poor transfer on 2nd side...
  5. Replies
    0
    Views
    3,642

    OCE TDS600 need service manuals needed.

    Thanks
  6. Bizhub Press C1060 Trail edge poor transfer on second side.

    12pt gloss about 270gsm, only on second side trail edge transfer is poor. Some sheets come out good but most have the issue, anybody run into this? :cool:
  7. Re: Texas A&M Study Calls Obama 5th Best President in America

    BLAH BLAH BLAH BLAH....don't waste your breaths fellow Americans. Until we take the money out of political campaigns nothing's going to change. Democrat, Republicans, Libertarian same old crooks...
  8. C454 intermittent lock up with Fax Ready and Scan ready message loop also OrangeLight

    What's more confusing is that it only does it at the customer's site. At our shop it worked fine for 2 weeks but when we take it back to the customer as soon as the network cable is plugged !!BOOM!!...
  9. Replies
    4
    Views
    2,206

    [CQ] Re: konica bizhub c454

    Yep, those lines are common when a step was missed in setup. When entering date and times in different areas of set up make sure to clear the current date and time even if it's correct, then...
  10. Replies
    2
    Views
    1,784

    Bizhub Press C1060_C1070 Pm Kit?

    I'm familiar with C500-C7000 pm kits, but unfortunately my dealer is rushing a C1060 out before I could get trained. Taking a quick glance at the manual and liked the replacement cycle for some of...
  11. Replies
    6
    Views
    815

    Re: Jamming every 46 pages on C6501

    20649

    Here you go sir.
  12. Re: Copystar CS5050 security risks for hacking into Hdd when connected to network or

    You have to get threw the network before getting to the copier. I always advise customers to seek the help of a good IT company to lock down there network and secure it.
  13. C6000 fuser jam does not clear, no jam code.

    I have a C6000 that has a jam condition, machine wants me to open front door and open M5/M6 doors to clear paper, no paper present. Also no jam code is displayed in counter that shows a jam occured...
  14. Replies
    6
    Views
    815

    Re: Jamming every 46 pages on C6501

    Did you take a look at the bulleting regarding J-9301 jam codes when duplexing? Check it out.
  15. Re: C6500 torn transfer belt after new drums installed

    Well your gonna have to by a new belt anyways, make sure to put a new blade and put plenty of kaynard powder to lubricate the belt. Turn it by hand and make sure the belt turns without alot of...
  16. Re: Konica Minolta C451 Issue - please help!!!!!

    "Still Printing Great - Just out of proportion" What is that suppose to mean? What is COGS?

    Sounds like your a print shop, so it's probably "Operator Error" or "Its the paper".

    Get a...
  17. Replies
    3
    Views
    1,257

    Re: Konica Minolta c224

    I would make sure the side door is not skewed, check the hinges. I did go to training on that machine and the door could cause problems with skew if it's not sitting straight on the machine.
  18. Replies
    9
    Views
    4,165

    Re: Bizhub C252 Fax Problem

    I encounter similar issues when fax machine is hooked up to a voip fax line. Try turning ECM to OFF and set baud rate down to 9600. Do you know if fax line is digital or analog?
  19. Wanted: SD-508 for Konicaminolta FS-526

    Thanks!!
  20. Anyone have an SD-508, saddle kit. Fits on a FS-526.

    Thank You!!
  21. Re: Wrinkling when folding, Konica Minolta C652 with FS536 and SD-508

    I'm going to replace the folding rollers and folding blade on and SD-508. Has any replaced the blade on a SD-508? I've searched in the manual but no dice, it looks really burried in there, every...
  22. Re: Wrinkling when folding, Konica Minolta C652 with FS536 and SD-508

    I told my field tech to clean the folding rollers when he 1st came up to me with this issue. If I go out there and that's what it is then my tech got lazy on me, I know those folding rollers could be...
  23. Replies
    9
    Views
    1,153

    [Misc] Re: bizhub c364 yellow pain

    I'm taking a shot in the dark and piont to the transfer belt, yellow transfer roller could be out of place or binding. DON'T Forget to do a new release so you could put the belt back in the box as...
  24. Re: c6500 - NG on Sub Scan for Manual Clr Reg.

    Possible beltwalking or knick on belt, whenever I've come across this issue it's been one ofthe 2. Try reseating cleaning unit making sure to thoroughly dust the belt andcleaning blade.
  25. Re: Wrinkling when folding, Konica Minolta C652 with FS536 and SD-508.

    Anybody, HEY GUYS!!
Results 1 to 25 of 92
Page 1 of 4 1 2 3 4