Search:

Type: Posts; User: costd

Page 1 of 17 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    1,142

    [Dead] Re: canon iradv2020 colour mc dead

    Each time I had this issue it has been the SATA Flash PCB. The cause was actually the low voltage pwr - and Canon sent out a free replacement PB for each machine - we bought the PCBs though.
  2. Replies
    5
    Views
    890

    [Misc] Re: IRADVC5045 - Load Paper message

    I think Tenatal has the right issue. You say it happens when set to auto - but not if a specific drawer is set. I suspect the document is of a size that is not in the machine and it is saying load...
  3. Re: Samsung SCX-5935FN with error: System error #02-000.

    Guess I may a jerk also - but being in the same group as BlackCat is not all bad.

    I cheated and have a manual - but just for the exercise, I took your exact subject line and did an internet search...
  4. Replies
    8
    Views
    2,562

    Re: iR2270/3570/4570 fuser film

    Could be the film (not all compatis are - we use Katun) or

    Did you do the nip adjustment? If not, I suspect the film just keeps walking to the end and ... In my limited experience rebuilding...
  5. Re: Sharp MX-3501N Finisher not stapling all the papers together. MX-FNX1

    Sorry for late response - I have found that over time, the grease on the guide shat becomes a bit tacky. I clean it all off and put a very small amount of oil on a rag, then wipe the shaft with the...
  6. Replies
    4
    Views
    1,562

    Re: iR Adv C2020 SATA-Flash PCB issue

    Thank you for the suggestions. As luck will have it, went to talk with the service manager and I saw the notice letter and low voltage power supply for this machine's serial number on his desk. ...
  7. Replies
    4
    Views
    1,562

    iR Adv C2020 SATA-Flash PCB issue

    Three times now the machine went into the "green light on but LCD dark" mode. All three times it was the SATA-Flash PCB that needed replacing. I figured it was a power issue, but across the street is...
  8. Replies
    9
    Views
    953

    Re: MX6200n Will not Calibrate

    My suggestion is to reload system software as it sort of sounds like someone loaded the wrong firmware (system with security kit has different SSW from regular systems).

    If they will not allow...
  9. Replies
    7
    Views
    2,179

    Re: Network Disconnection Problem in KM-2560

    Not sure about Kyocera, but Canon and Sharp have a problem with MFP dropping off the network when it is GigaBit. Two solutions that have worked for me is turning off SNMP, or placing a hub between...
  10. Thread: MX-C311 Scanners

    by costd
    Replies
    13
    Views
    2,275

    Poll: Re: MX-C311 Scanners

    I am not so sure they are air tight (Sharp's claim not withstanding). We had a customer really bothered by the "fog", so we pulled off all the stuff and was able to clean the glasses. Not fun, but...
  11. Replies
    8
    Views
    1,152

    Re: different finishing trays

    Not sure if this is what you mean:

    If I have a print job I want to go to tray A, then in the printer driver, finishing settings, I can change Auto to A - or B if that is what is wanted.

    So,...
  12. Replies
    5
    Views
    1,391

    Re: Sharp MX-2600 Black Line on copies

    Step one is to find an actual service tech as this is so basic even I knew it by the end of my first day.

    Look at the lines - do they go all the way across the page without a margin (I suspect...
  13. Replies
    5
    Views
    1,299

    Re: Differences between AR-M455 & MX-M450

    fusing assembly (actually the frame itself) is different. Same parts to rebuild though.
  14. Replies
    7
    Views
    2,303

    Re: Canon ir5570 E0014

    Your milage may vary - even with the new bearings and following the TP, some units still had the same issue. Canon then released a pressure roller unit that had bearings pre-installed (FM2-4683). ...
  15. Replies
    3
    Views
    1,795

    [Misc] Re: MX2600n printing over the internet?

    We have several USDA FS machines scattered around and they all are able to print to any machine. They do not have a VPN, but they do have a WAN.

    If it use to work, but stopped - ask IT if they...
  16. [Jamming] Re: Canon IRA5051 unable to get test page or do auto grad.

    I think he is right about checking the instructions. It is possible you forgot the steps BEFORE inserting the passthrough. Kind of seems regular output may be making it to the finisher via the...
  17. Replies
    4
    Views
    1,141

    [CQ] Re: MX-2300N Missing cyan

    As your service tech should know, the gritty is the developer itself. If you do not have a tech - you need to call one before you get in deep (read costly).

    A wild guess is the developer was...
  18. Replies
    12
    Views
    3,444

    Re: iRC3380 display blank

    Just for sh*ts and grins, check to see if it will come up in download mode. If it does, try reloading the system software. Never know, it could be a crashed HDD vs one that is just good enough to...
  19. Replies
    5
    Views
    1,976

    Re: how remove the sorter of ir3570

    At times it would help if you include the error message you are getting.

    Just taking a wild stab at it - I suspect you are missing the trays and flags that are removed when installing an S1...
  20. Replies
    7
    Views
    959

    [Electrical] Re: canon image class D 880 (no display)

    The LED being on just lets you know it has some power - not if it is enough. I suspect you did more than just remove the rear cover as these units will function without the cover. Take the cover...
  21. Replies
    9
    Views
    1,803

    [Misc] Re: canon cassette broken guide gear bins on base

    Unless you are just trying to drum up business - the Canon solution ends up being less than a penny. No idea what the plate you are selling costs, but I suspect it is more than a cent. Long long...
  22. Replies
    9
    Views
    1,803

    [Misc] Re: canon cassette broken guide gear bins on base

    We just drill (or file) the hole a bit larger and use a metal post (Canon tech Pub - do not remember the article number).
  23. Replies
    6
    Views
    831

    Re: Line when printing - but not copying

    JAWS: SB does not apply. Even if I am not rebuilding the units properly, the issue would go away when I put in an MX-27NUSA - and it does not. Thank you for the suggestion though.

    HEMLOCK:...
  24. Replies
    6
    Views
    831

    Re: Line when printing - but not copying

    Thank you for the reply. As I should have said, I have tried new units (MX-27NUSA) as well as rebuilding with the MX-27NRSA and MX-700MK and new seals/pads as required. Same results.

    Replaced...
  25. Replies
    6
    Views
    831

    Line when printing - but not copying

    MX-6200 (3 different machines - same location). Started with magenta on machine 1. They appear at random times but in same location (leading to trailing front edge - as in bottom of a page). They...
Results 1 to 25 of 416
Page 1 of 17 1 2 3 4