Agreed, this is an excellent way to verify if it is the board or Msata that is causing the error. Hopefully you can fix it with the first component every time once the issue has been verified through...
Type: Posts; User: austonrush
Agreed, this is an excellent way to verify if it is the board or Msata that is causing the error. Hopefully you can fix it with the first component every time once the issue has been verified through...
I'd 100% replace the hdd, this is a pretty common jam issue for this series of Sharp once the hdd gets older. New HDD should get you back up and running smoothly
I don't know, I would not have taken 3 eeproms from a different machine and put them into a different copier. I would strongly recommend you change out all 3 with new ones at the exact same time, do...
HP Doesn't make those ADF assemblies serviceable other than replacing the feed roller kit. I've seen your issue before and it can be caused by a damaged wire in the wiring harness for the adf. They...
I don't believe HP ever made these, but you can find 3rd party aftermarket ones, that work just fine.
Just search for HP M479 mylar strip :)
Iteminc.com is the only North American distributor for Oki now. Did you check with them?
It depends on whether the partition is encrypted or not. It works on some machines. Never had any luck with plotters though. Worth a shot to try on a couple of the newer E77XXX ones and see.
As Spud42 said,
you need to use an HP HDD, however, once you have a good drive you can create a clone of it with hdd raw copy tool and store it for future used. You'll then be able to use any SSD...
You'd hope when buying a brand new fuser this would be done at the factory.... ugh lol. What happened to just installing a fuser and being done!
I have not done this adjustment with any new out...
Glad to hear that suggestion helped. Yes, normally most plotter throw a code when the carriage assembly isnt going back to the correct home position. But with the T520 and T530 I have had this a...
It's quite possible the PH is defective. If you can get it replaced under warranty, start there, then you know!
When you installed the new printhead did you install it with the 4 brand new ink cartridges it ships with?
Does the printhead dock properly over the service station once a plot has been...
if the labels are actually one single sheet sized at 8.5" x11" then I'd recommend a lexmark MS725dvn printer.
If they are smaller then get a proper zebra type thermal transfer printer in there!
...
For all those interested I was able to solve this issue
The cause was broken staples caught in the the track for the front alignment motor arm
Resolution:
- Pulled apart finisher, cleaned out...
Hello Everyone,
I have a MXFN11 attached to a MXM565 that is having vertical alignment issues on finisher output and it won't staple properly. Please see attached image
It seems to be some type...
These fusers require maintenance or they fail. You need to run the Fuser Cleaning Page on all these units on a semi annual basis, run at least 20 pages to start
Settings Icon (wherever you...
Thanks for the quick response guys. I have already swapped the fuser onsite so I know it is the fuser that is the issue. I'll do a visual inspection on the belt and sensor and see if the belt has...
Hey Guys,
I have a Sharp MX407FU1 Fuser that I need to fix. Service Manual Says the TH_US2 Thermistor is the issue.
I cannot find this part number in the parts manual.... Anyone know what it...
Latest Update -
This time we Replaced all 3 EEPROMS with new ones in one go (PCU EEPROM, SCN EEPROM and MFP EEPROM), and forced the copier into CN Mode on first bootup.
Once the firmware...
So we did this and everything matched up. Which shouldn't be the case...
You're wasting your time without a new blade!
There's no manual for rebuilding them as far as I know. Take some pictures of the gear assembly layout around the blade before removing them. It comes...
Hey Guys,
Has anyone here had a U2-00 error code before?
I've replaced the SCN-MFP PWB and MFP EEPROM as well and I still have the same error on bootup.
I'm think of changing the PCU...
An authorised dealer needs to contact sharp directly to get a reset code for that model.
Hey Guys,
The most common cause of toner jamming on all these newer hp toners is the drum dongle gear. Either the spring pops off, or one of the 2 pins will snap completely. See image below:
...
As you are an end user and not a tech I would strongly suggest you keep all screws with each component and repair it in a very orderly fashion, stacking everything up neatly in the order you remove...