It wouldn't copy or print when I got there. just a white screen. cannot get a screen in any test mode either. so Ive taken apart control panel reseated all connectors, also reseated dims on main...
Type: Posts; User: Bri Ski
It wouldn't copy or print when I got there. just a white screen. cannot get a screen in any test mode either. so Ive taken apart control panel reseated all connectors, also reseated dims on main...
Thanks, whatever it was on the mirrors or ccd and lens I tried water first, no luck, then Wiped em all with cleaner and boom. Nice. 23 years doing this and I only had to use a glass cleaner when...
Seems to be just light and it does it through ADF so the lamp is stationary and at home position. when you darken the light center starts to go away and rest of image gets "dotty" dark, but not the...
I've seen this and cleaned optics and its been fine after. This time its made no difference. Copies off glass and through adf have about a 1 inch light stripe from left to right down the middle of...
Machine seems ready but will not print or copy Screen is black. is there a reset you can do without a reset tool? If so which buttons would you hold at power up, and Furthur procedure? Only have one...
Its definately the buttons on top the fuser
when scanning and i am not getting the panel choice for multi page documents. Is there a SETTING to enable this? On the lcd panel I choose scan. then fyle type, select PDF and still get no choice on...
turned switch off wouldnt power down. Unplugged and then it powered on and off like normal. that was weeks ago, now it will not power up.
switch seems to test correctly, i have lights on main board...
on an 11x17 print from top to bottom the first 14 1/2 inches is perfect. The last 2 1/2 inches the color is way off. It appears it is dropping the yellow from the print and is a hue of red. For...
Just got this one in. Finisher was tweeked. Any common cause for this particular code? Thanks for any suggestions
11mm bandlines. the space magenta to yellow is about 82 mm, then from yellow to cyan its 115mm, then cyan to magenta is 82mm. Other wise prints look good.Customer say they've seen ghost image but i...
the copy/fax/scan lights all lit green. process data lit green, error lit red and the lcd is blank. It will print but will not copy or fax. any thoughts? thanks, Bri Ski
It is OEM toner
Usually one of those things resolves this problem. seems to only be doing it with black,
tried three diff black toners and a new fuser. still does it. tried paper settings fromm thick to thin, no...
cannot get from canon website, anyone know how to get?
If its not cosumables or transfer.this and similar models can collect dust on the laser unit mirrors. on the inside of the units. have a few that need cleaned once or twice a year
secondary codes status lit red, toner lit amber, by holding down go and cancel
I think its the laser or board, sounds like the laser motor starts to go and immediately all light flash. Thanks for...
Cross references to a ricoh1180L
It could be that the thermal fuse has gone bad. I checked usual vendor and they only have whole fuser for 200$ Told customer didnt want to take apart till i found...
talk to don at cadd engineering, deals with all brands and types of wide format 800-831-8587
Tsa complete units are good!
to left slightly and above drum unit.
the laser slit glass can get clouded with toner mist and cause light prints. it faces down just to left of drum unit
have to remove developer and drum to wipe off. If thats not it can be bad...
Went to machine cleaned it very well. did not have any feed issues. Customer says its doing it again, Quits running during a 50 page run and thinks it needs paper.
I went back, had them run same...
Has anyone seen this in the display and resolved? no fault code, just that message on screen. when plugs are removed from harddrive in network controller same message
when usb removed from display...
Has 27k color images and 167k b/w. 194K total. color images are faint and washed out like bad developer color not bright or crisp at all. Dont have this manual, thought it may be due for p.m. Black...