Does anyone know where I can get a parts guide and parts for this machine. All I need is Tray 1 feed rollers and length paper guide. The guide is broken so the paper slides away from the paper feed...
Type: Posts; User: travi
Does anyone know where I can get a parts guide and parts for this machine. All I need is Tray 1 feed rollers and length paper guide. The guide is broken so the paper slides away from the paper feed...
We have a customer that has setup virtual printers for coin-op printing using EnvisionWare LPT One. When they select multiple prints of multipage documents duplexed, they receive all of the page...
I have an MXB467F that prints out light pages when printing from a computer and making copies. Faxes and internal test prints will print normally. I have checked and cleaned drum contacts. Checked...
Check the sensor in the toner motor unit. We have had a couple knocked out of position. Even had one broken in to two pieces
I have an E67660 that gives an Error 49.38.0C.
It also has given codes 44.01 and 44.A0.4B. The firmware has been updated twice. The print memory cleared a number of times. Is it time to replace...
I had a MX6071 do this six weeks ago. Customer was using non-OEM toner. Replaced Toner motor assembly and PCU board
We sent the machine back. Our Sharp RSS said to check the toner cartridge connector. I would check all the connectors for the wires that are in the wire harnesses that this wire runs with.
We have a brand new out of the box MX-C407F that only prints blank pages. It does not matter if print or copy, color or black & white. When stopping the process in the middle of a job there is no...
Found the network was set to public. When I changed it to private in network type settings and the antivirus software, it was able to scan. Thanks for help.
I have a Sharp MXC407F (Lexmark XC4140) that will not scan to a network folder. When I test the connection on the MFP it tells me "Invalid Network Folder Address". The scanning was working for 3...
Does anyone have an display available for an Oki Microline 8810. Part number 41590601. PM me with contact information.
Thanks
I have been told by Sharp reps and in class that Sharp supports a machine 7 years after the date of last production. That was before the Foxconn take over. I have not seen anything published on...
Swap each color drum unit separately with the Black drum unit. The code will change from C1-14 to C1-10 when the problem drum unit is installed as the black drum. You said that you are on an oil...
I was finally able to reach Panasonic. They sent me a copy. Thanks
Does anyone have a parts manual for an UF-7200? I have the service manual and the parts manual is not available on Panasonic's partner portal.
Thank You
Does a Canon iR1730IF support SMB 2 or 3? Does it support above TLS 1? I have a customer the turned off TLS 1 and lost scanning to network folders.
Thanks
Does anyone have a service manual for a Xerox Workcentre 7242. I have a customer that picked one up from their sister company and would like me to service it. Thanks
Since I don't have a service manual and normally don't work on Xerox. I don't have the life of the consumables. The total counts are 170773 black and white, 7823 color. All I have done is cleaned...
I have a customer that inherited a WorkCentre 7242. the black and white output has background and looks like it is out of focus. The edge that is near the rear of the machine only has backgound no...
As far as Sharp USA is concerned they no longer exist. Japan has not released them to anyone.
Take a look at MFP-TB-1549. It is for the MX4070 but works for this machine. There is a new tension spring I have had success with it.
One of my Sharp copier customers has on of these in a small office. I need a service manual to fix it for them. It is printing a blurry line of black text about every inch and a quarter
Thanks...
Which harness LSU to PCU PWB or LSU to W-ICU PWB? Any common breaks in the harness? Did you install a new harness or repair the old one?
Thanks
Travis
I have replaced LSU, PCU PWB, DC Power supply, and W-ICU PWB. I have also updated the firmware. Any ideas on what I am missing.
Thanks
Travis
Sorry for wrong number for the drum. I mistook the model for the FO-2080.