Success! I was able to repair my machine. It was NOT a pinched wire harness. The actual solution to my problem was fresh developer and a THOROUGH cleaning of the NEW toner hopper (not the recycling...
Type: Posts; User: tricotech1
Success! I was able to repair my machine. It was NOT a pinched wire harness. The actual solution to my problem was fresh developer and a THOROUGH cleaning of the NEW toner hopper (not the recycling...
This sounds just like the Canon finisher problems with pinched wire harnesses. I will check them. Thank you for your help.
I appreciate the info, I will check the harnesses today. The machine has only about 450k on it. Thanks.
Hey guys, I have an E-Studio 720 with a CF70 and I am unable to make a change in the machine. Customer's initial complaint was that the copies were washed out, but before I could arrive the machine...
It has been awhile since I had this problem, but due to noise or other issues the machine requires a DC controller reset or an MMI reset. In a worse case scenario, I needed to replace the HDD...
Hey guys, I am looking for the actual doctor blade gap adjustment for a developing unit for a Canon Imagerunner 5020. I have poor copy quality from front to rear. I found the gap is out of...
P.S. How can I print out a function list when the machine has an alarm message? I can't exactly see the firmware that way. I imagine I can see it in service mode somewhere?
Thank you for the update on the software version info.
And as far as Mr. "manuals for you". Thank you, but I have the manual and it is worthless for this issue.
I am getting this exact message on two different machines. Both have "genuine" toshiba cartridges in them. It appears the CSIC pba is in contact with the bottoms of the units. Both of these...
Icing on the cake. I am ALL excited to go and resolve the issue at SECOND machine I mention previously in this thread. I go to this customer 1st thing this morning. Get the software loaded and I...
Well, for those of you that are still interested in this thread, I have FINALLY found a solution to my problem. I needed PDL downloader, because I have the 1st generation C1 controller. The Fiery...
That is true. If you blindly send a board to Hytek, they will charge the repair price for that board. BUT, if you ask for the board to be tested first and it tests good, they will only charge a...
Thank you for the instructions teckat, but as I have said before, I have followed those directions exactly and I can't get past the CONFIGURATION screen on the copier. So, I would like to try the...
You could always send it to Hytek in Florida. Repair price is cheaper than ordering a new one and you get a year warranty on it. Just a thought.
Thank you for everyones responses. Fortunately, I think the customer has given up on this older machine. I delivered a Canon IR-C3200 to them a week ago and they haven't asked me to fix their...
You guys are right. Is he a tech or an end user? My bad. Fortunately, he has not responded yet.
If you are talking about letting the Fiery tool guide me, you are correct. I have followed that procedure. It looks like the software uploads correctly, but the copier only goes into CONFIGURATION...
I have the old style C1 controller. The one without the power interrupter board. I have version 1.1.1 software on it. When sending a print job, it can only print 1 set at a time. No matter the...
Check your email.
Minoltas are not my strong point. I will go and clean sensors in and near the drum unit. But I still don't understand how that would prevent a bottle from turning. The augers turn. The developer...
UPDATE: I suspect there might be something to do with trying to update the software from a laptop with Vista. Upon recommendation from a person at Hytek, he suggested I try all the same steps, but...
No, I did not replace the developer. The only things I did was replace the upper fuser picker fingers and replace the transfer corona wires. The machine runs about 3 copies and then says "add...
Well, I have finally found a G1/C2 system software CD for my C2 controller. I went to try to load the software. I install the cd into my laptop drive and let the Fiery installer do it's thing. ...
I have a Minolta Di 470 that runs a few copies, then says add toner. The toner bottle never turns. The bottle is full. It appears that the auger past the bottle turns, but the bottle itself never...
I have an e-studio 450 and intermittently as the paper exits into the upper tray it folds the corner on the front frame side. I have been a tech for some time and know to look for torn or folded...