Could it be IDC sensor issue? I put a piece of clear self-adhesive vinyl in front of it and after the gamma adjustment the voltages are much higher, about 800-900 V, but all colors, including Cyan...
Type: Posts; User: kandod
Could it be IDC sensor issue? I put a piece of clear self-adhesive vinyl in front of it and after the gamma adjustment the voltages are much higher, about 800-900 V, but all colors, including Cyan...
They are OK visually, cleaned them with isopropyl, I will check for leakage to the ground.
Thats the gamma adjustment screen, noticed the Cyan voltage is lower than the others, how can I...
Hi, the problem color is Cyan, cannot reach desired max density (~1.4), current is 0.95-1.00. Changing Max Density Adjustment in Service menu does not seem to have any effect. All the useless...
All 4 Write units are identical partnum A1DUR70U00.
No procedures are needed, just swap the units (and remember original position) and DO NOT write initial position memory. You can also use...
When executing Chart Adjustment, Mag. Skew Adjustment is performed automatically (to compensate face-back misregistration due to image skew). When Mag. Skew Adjustment value changes Color...
Thank you for your response, these issues with the vertical conveyance door (and the transfer carriage guiding pin, clipping the humidity sensor wire) are well known and checked as not being the...
Hello, can someone with access to official konica minolta techical resource site (not sure what is its name) check for some bulletin (or whatevet it is) regarding these two errors. The reason is I...
Can you please give me info or quote here the procedure to check for the issue. I dont have access to konica service site, and really would like to know how to avoid belt replacement on a low counter...
Interestingly you keep mentioning that spacer, can you give some info on how to accuire one of theese, because no trace of it in the net.
Is that the trailing edge? If it is the inboard edge instead, try putting some tape on the drum plate where it touches the dev unit yellow bearing (increasing a little bit the distance between the...
Firmware version before was: P Control C -> A1DU0Y0-00C1-GPY-40
According to the manual G00-xxxx type of firmware is needed for A1DUH030 type of board. The old one is A1DUH830.
Didn't know that was possible. How can I copy them? Followed procedures in service manual error C-C101 and after replacing the ICP23 fusable link the old PRCB starts but then C-5002 comes and the...
Can someone help me find a firmware for this machine, I got error C-C101 after replacing the PRCB. The new one has A1DU rev.00 written on one of the chips and A1DUH030 C0022851 number printed on the...
Found the problem, the fuser roller /2 metal bearing was set up improperly with the limiter from the outside, very stupid mistake, thank you for the help!
Thank you for the replies, i have replaced the belt and almost immediately the inner edge pressed towards the regulating sleeve
33008
Any ideas? Thank you?
When replacing fuser belt, the two rollers inside are covered with some sticky material, it is probably the special KM grease. So the question is should I clean them before putting the new one, and...
It is not the cleaner that causes the problem but the cleaner retract clutch - a device that rotates the cam shaft that lifts up and down the cleaner blade as the belt rotates. When the image is...
Almost allways that kind of problem is caused by a bad IBT cleaner retract clutch (121K17941), so check this first (or replace if a new one is available).
I see that you have tried changing the 2BTR, but if you have marks on the back the only suspect is the 2BTR unit.
Check the spring that moves the belt edge sensor, I had the same error but with DC2060 after cleaning the interior of the machine I had accidentally unlinked it. There is a thread in this forum...
I have exactly the same problem, it just happen from time to time with different kind of papers and sizes more frequently during the second side printing. I think it is connected with the failure...
The oil looks normal. What I noticed however, were the two red screws that sit just in front of the fuser nip adjustment screws (hidden under the belt finger assy plate) and as far as I see they are...
Hi all, I have this problem with Xerox Docucolor 2060 for a long time already, image not fused evenly in centre-to-INBOARD and OUTBOARD direction, and the result is some colour shift along the edges...
GusG, have you tried to change the MOB sensor?