While running the C6500 32page saddle stitched booklets with front covers inserted through the Post Insertion Tray 1 the copier would run consistently 13 booklet and error out at the end of the...
Type: Posts; User: copycorner
While running the C6500 32page saddle stitched booklets with front covers inserted through the Post Insertion Tray 1 the copier would run consistently 13 booklet and error out at the end of the...
Yes, the code is gone but I can't recall any jobs or store any jobs because the recall and store button won't light up. It's like the HDD is not there or it has been turned off somehow.
Yeah, I got a used seagate drive from the computer store across the street. Then I realized, after going through the manual, that they are preformated. Now I'll have to go to KM in the morning to...
I have an SC49-01 pointing to the HDD2. I replaced the hard drive but the submenu for formatting all is not highlighted so I can't format the new drive. Am I missing something?
Thanks, I think you're on to it. I'll try to trace it back.
I can't get the bypass tray to recognize the right size paper. I switched the bypass tray with another machine and the copier will still not recognize the right size paper. Sometimes it will work...
I'm continuing to have intermittent problems with an FS-503 finisher attached to a SD-501 saddle stitcher on a 1050e. After the stapler staples the set it fails to exit the finisher but the copier...
This machine continues to have problems around the drum assembly. The print quality is good but jams. The paper does not release from the drum. If the paper does make it past the drum assembly it...
When starting the hv auto adjust the machine will only get to 3/8. The paper is rolled up going into the fuser assembly. Any suggestions?
Just found a ground wire came loose from the HV power...
When I plug in the FS 503 finisher to the saddle stitcher the only way the finisher is recognized is when I leave the front door interlock open until after the copier boots up . Then if I close the...
I have a perfect binder that I swap with a FS-503. I would get stapler problems intermittently and it would jam with the stapler head down
through the set and then would say "finisher is now...
Thanks for the reply albasoul06. I'll start with the sensor.
After power up the scanner does not light or move. Fault code SC41-03 displays. I blew out the home sensor and I rotated the drive moter by hand and moved the scanner out of home position and...
I have both a docucolor 240 and 260. I will keep the docucolor 260 loaded with really new consumable, ie new drums, IBT belt. The 260 now has signs of a light strip of low density void,(very faint)...
I replaced the broken corona with a discharge corona. I did notice that the wire was silver, not gold
colored like the previous one. Also, I did remove and replace the HV supply from the back of...
Started when I turned the machine off, exchanged the stapler fs-503 with the perfect binder pb-501
and then turned the machine back on. The first error code was a sc28-04. I replaced the ADUBD1...
I replaced the AUDBD1 board $750.00 (ouch!) and when I removed the old board I did check the icp5 and did actually confirm it was open, Thank you albasoul06. Now when I turn the 1050 on it goes to a...
Thank you so much. Couldn't find that. Didn't really want to hear about replacing that board. Probably not cheap and there's 2 days of down time. Any way of repairing the board?
Sorry, the machine with the sc28-04 error code is a konica minolta 1050
The error detection signal (blowout of a 24V fuse) of the high voltage unit /2 (HV2) is detected.
Found the broken charger wire and removed it and the eyelet ends. The machine powers up and goes to...
I have a Konica Minolta 1050e with both the FS503 and a Perfect binder that I alternate on and off with.
The problem started with the stapler not finishing its cycle and stopping with the head...
OK,
Back in order. The new motor fixed the problem however after reading the post from RRodgers I was able to locate the Fuse F1 on the motor circuit board and checked for continuity and it did...
I just checked the motor board but I don't see anything resembling a fuse of curcuit breaker reset or anything. You'd think there would be something for just such an occasion would'nt you.
Yes, the blade did flip. Now the drum motor won't operate.
I ordered a new motor coming today but really don't think that's going to work.
I'm afraid the Printer control board is the problem. I...
Si@danwood,
I was able to check the continuity through ICP12 and ICP13. Each check out OK for continuity. The only other thing I can do is to check for the 24v to the motor connector from the...