Search:

Type: Posts; User: withnail

Page 1 of 3 1 2 3

Search: Search took 0.31 seconds.

  1. Replies
    23
    Views
    4,091

    Re: MPC3503 won't print out faxes

    I take it you mean Reception File Settings/Print turned on? Yes this is set to on with forwarding and store set to off. Locked Reception file is also turned off on the same page
  2. Replies
    23
    Views
    4,091

    Re: MPC3503 won't print out faxes

    I changed Auto reduce to off when I returned for the reports to see if it changed anything which it didn't.
  3. Replies
    23
    Views
    4,091

    Re: MPC3503 won't print out faxes

    No none of the trays have any labels on them so all plain. Tray 1 is locked as it has yellow paper in it but I have turned off the lock and no change.

    Fax tray is set to auto in Fax User Tools RX...
  4. Replies
    23
    Views
    4,091

    Re: MPC3503 won't print out faxes

    As requested here are System Parameter, User Parameter and Non Defaults lists
  5. Replies
    23
    Views
    4,091

    Re: MPC3503 won't print out faxes

    With reception file set to Print only the prohibit function isn't selected, I have been through every option in reception settings and everything is set as normal which is why I'm a little stumped...
  6. Replies
    23
    Views
    4,091

    Re: MPC3503 won't print out faxes

    Yes have tried leaving Fax Tray set to auto in reception settings and T2 in Tray Paper Settings then when that had no effect just tried changing to all of the 4 trays, no change
  7. Replies
    23
    Views
    4,091

    MPC3503 won't print out faxes

    I have a MPC3503 that will send and receive faxes ok but won't print them out, There is no forwarding set just print all faxes but all rx faxes simply go into memory and the fax received light comes...
  8. Replies
    3
    Views
    6,788

    Re: MPC8002 giving SC381-01, 02, 03, 04

    Thanks for being the only one to reply! Only the Y code would be visible on the display (SC381-04) but all other codes were listed on the SMC at the same time.

    The fault was caused by the I/O...
  9. Replies
    17
    Views
    8,570

    [Misc] Re: MPC3502 VOIP Not Receiving Faxes

    Try turning off the V8 protocol
  10. Replies
    3
    Views
    6,788

    MPC8002 giving SC381-01, 02, 03, 04

    I have an 8002 which gives all four codes, I have replaced all 4 drum potential sensors and the power pack boards for KMCY units. The quality of the copies is perfect but when it performs a MUSIC...
  11. Replies
    5
    Views
    2,032

    Re: mp 4001 toner issue

    Strip the toner hopper and check the 4 mylar paddles haven't come unstuck
  12. Re: MP C3003 harness cable of DF3090 to the machine

    As the other guy stated wiring loom part numbers are in the point to point not the parts list usually.
  13. Thread: aficio 2045

    by withnail
    Replies
    6
    Views
    747

    Re: aficio 2045

    Pull the paper feed unit out, there is a mylar that is hard to see when its in the device but it can tear or come unstuck.
  14. Replies
    4
    Views
    1,370

    [Misc] Re: MP CW2200 no paper detection

    Make sure the black bed that the dress sensor looks down on is free from paper dust, have had dusty machines do the same.

    Other issues have been the roll not on straight even when it looks fine,...
  15. Re: MPC4503 copy quality issue in colour text/photo mode only

    Thanks for the replies so far. To answer you all, ACC has been done many times, the NVRAM data has been reloaded from the original run up so any changes in SP causing this would have been...
  16. Re: MPC4503 copy quality issue in colour text/photo mode only

    All other print outs such as printer test page and ACC scales are fine, the optics are spotless as other original type selections such as text, generation, photo are in perfect quality when copied.
    ...
  17. MPC4503 copy quality issue in colour text/photo mode only

    I have faint colours when copying in colour text/photo mode only, any other mode in colour is fine, single colours are fine. Have reloaded the NVRAM data from original run up, replaced scanner block,...
  18. Replies
    1
    Views
    516

    MPCW2200 not loading paper

    I have a problem with one of these not loading from the roll. Paper feeds in and out but doesn't cut then is reversed on to the roll again saying Load Paper, no jam. It only has one roll which is on...
  19. Replies
    2
    Views
    1,668

    MPCW2201SP staying in Japanese

    I have a MPCW2201 new out of the box which was run up fine, it was powered down and moved within the building and booted up in Japanese. Fine if we were in Japan but I'm not and neither is the...
  20. Replies
    6
    Views
    1,429

    Re: Ricoh SPC242sf calibration

    Check toner saving isn't turned on, that gives lovely washed out copies if you like that sort of thing
  21. Replies
    8
    Views
    7,523

    Re: RICOH MP CW2200SP B jam

    Check the encoding strip for the carriage isn't damaged where it sits on the black runner, if it is the carriage won't know its horizontal position and the fun starts.
  22. Replies
    22
    Views
    3,766

    Re: Ricoh MP C2800 - 5 minutes to boot

    Set Fuction Priority to Copy in System Settings
  23. Replies
    15
    Views
    3,015

    [Misc] Re: Aficio 2075 Fusing Problems

    If there are 3 lamps on this fuser check that one of the filaments isn't broken. I've had similar issues where the fuser warms up enough with one lamp blown but after a couple of days gave the same...
  24. Re: MP CW2200 poor image after print head replacement

    Am guessing you changed the K print heads only? Might be worth retracing your print head replacement steps in case its not fitted correctly.
  25. Replies
    35
    Views
    27,901

    Re: MP3353 sc672-11

    Have since replaced the USB lead from the IPU and Ops Panel to cure this fault.
Results 1 to 25 of 60
Page 1 of 3 1 2 3