Search:

Type: Posts; User: lazo7

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    3,324

    Re: Xerox Workcentre 7220 won't boot up

    The machine is working after all.
    I just left it boot for about 20 mins after upgrade. And now its working. :D

    Thank you very much gnr115 ​for your help.
  2. Replies
    3
    Views
    3,324

    Re: Xerox Workcentre 7220 won't boot up

    gnr115, thank you for a quick reply.
    I've managed to upload new firmware via USB drive using ALTBOOT like you suggested, but no luck, the same problem persists.
    The machine trys to boot for few...
  3. Replies
    3
    Views
    3,324

    Xerox Workcentre 7220 won't boot up

    Hi everyone,
    I have a problem with Xerox Workcentre 7220.
    The machine doesn't boot up. After about 15 minutes of booting, the machine displays message : "the device is not available turn off the...
  4. Replies
    9
    Views
    8,271

    [Error Code] Re: Canon iR-ADVANCE C2020i E000020-0091

    I have even swapped a hopper from another machine, even that didn't help
  5. Replies
    9
    Views
    8,271

    [Error Code] Re: Canon iR-ADVANCE C2020i E000020-0091

    Allready done that, no luck :confused:
  6. Replies
    9
    Views
    8,271

    [Error Code] Re: Canon iR-ADVANCE C2020i E000020-0091

    No, I've opened it by hand when it was all disassembled...
  7. Replies
    9
    Views
    8,271

    [Error Code] Re: Canon iR-ADVANCE C2020i E000020-0091

    Thank you freebyrd116. I have allready removed lasere assy and cleaned dustproof glass, but no luck with that
  8. Replies
    9
    Views
    8,271

    [Error Code] Re: Canon iR-ADVANCE C2020i E000020-0091

    Thank you zoraldinho. Tomorrow I'll try doing what the bulletin says. I'll keep you informed. Dustproof glass is clean.
  9. Replies
    9
    Views
    8,271

    [Error Code] Canon iR-ADVANCE C2020i E000020-0091

    Hi, I have a problem with Canon iR-ADVANCE C2020i. It keeps giving me error code E000020-0091. A new yellow drum was installed, didn't help. DC controller and laser assembly were also replaced, new...
  10. Thread: IR 5055

    by lazo7
    Replies
    5
    Views
    1,095

    Re: IR 5055

    It works, maybe you'll only have to adyust wire height
  11. Replies
    5
    Views
    2,517

    Re: Canon iR 2270 making waves on A3 paper

    Thank you all for helping me. After changing the values in service mode, everything worked well. :D
  12. Replies
    5
    Views
    2,517

    Canon iR 2270 making waves on A3 paper

    Hi everyone!
    I have a problem with couple of Canon iR2270. When you print or copy on A4 paper, everything works fine, but when you try to copy or print on A3 paper, on allmost every sheet i have...
  13. Replies
    12
    Views
    12,123

    [Error Code] Re: Canon iR 1022if SYSTEMERROR E354

    I'll do that first thing tomorrow. I'll let you know did it work. Thanks
  14. Replies
    11
    Views
    3,206

    [Misc] Re: IR3300 Printout rubbing (poor fusing)

    I agree, the best thing is to install new genuine fixing unit. If not, try to change heating element of the fixing film assembly. Maybe you didn't assemble fixing unit correctly, and the pressure...
  15. Replies
    12
    Views
    12,123

    [Error Code] Re: Canon iR 1022if SYSTEMERROR E354

    I took the board from another copier. Thank you very much for your effort. I'll try to contact Canon, and see what they say, but I think in that case that the repair will be more expensive than the...
  16. Replies
    12
    Views
    12,123

    [Error Code] Re: Canon iR 1022if SYSTEMERROR E354

    I have another machine that doesn't have fax or network (iR1018), but it has that same board :confused:.
  17. Replies
    10
    Views
    1,913

    [Misc] Re: blank copy problem in ir 2830

    I had similar problem once on iR 5570. After changing everything ( laser, DPC sensor, HV board etc.....) we have discovered that the problem was in loose connector on pre-exposure lamp. Check...
  18. Replies
    10
    Views
    1,913

    [Misc] Re: blank copy problem in ir 2830

    Do you have blank copies when you print as well? Or is it just when you are copying? Did you get any error messages in the past ? Try going to the service mode>copier>display>err to see if you had...
  19. Replies
    12
    Views
    12,123

    [Error Code] Re: Canon iR 1022if SYSTEMERROR E354

    This is how the board looks like. It has a code on it : FM2-2801. There is nothing like that in parts manual :confused:
    23874 23875 23876
  20. Replies
    12
    Views
    12,123

    [Error Code] Re: Canon iR 1022if SYSTEMERROR E354

    The counter board has not been replaced at all, only the board that has "SOFT-ID" written on it. I will take a picture of it tomorrow, and post it.
  21. Replies
    10
    Views
    1,913

    [Misc] Re: blank copy problem in ir 2830

    Did you try stopping the machine in the middle of the copying procces, so that you can see is there image on the drum surface ?
  22. Replies
    12
    Views
    12,123

    [Error Code] Canon iR 1022if SYSTEMERROR E354

    Hi,
    I have a problem with one of our copiers. I had to replace SOFT-ID board, and now I am getting error message : SYSTEMERROR E354. That error has something to do with the serial number mismatch,...
  23. Replies
    5
    Views
    1,614

    Re: Konica Minolta Bizhub 163 toner dosage problem

    The error was C0F32.
  24. Replies
    5
    Views
    1,614

    Re: Konica Minolta Bizhub 163 toner dosage problem

    Yesterday I flashed new firmware, and it looks it will be ok now. After flashing it , I executed toner replenishing, and the machine reported error C0F3. Before flashing the firmware, it never...
  25. Replies
    5
    Views
    1,614

    Re: Konica Minolta Bizhub 163 toner dosage problem

    I'll try to flash the firmware in monday. Maybe it will help. I'll keep you informed. Thanks for reply
Results 1 to 25 of 52
Page 1 of 3 1 2 3