Search:

Im not sure what you mean by presser?

Have you checked the rollers on the paper exit section above the fuser. sometimes they can move out of position, which will cause this issue.

Hello

Anyone have a fix for brand new kit coming out with most recent papercut on and devices freezing/rebooting and occasional E301 codes.

C558
Function Version 4.1
F/W GC2-R9
PapercutMF...

It automatically installs the one windows picks up when you plug in via usb. However, I tried to load the PCL driver, off the Konica disc, but it just hangs. There is a rundll32 hanging in the...

Greetings

Any of you guys had the issue of C3110 connected via USB for printing, only doing one copy of a job. ie. 3 page doc and you want 4 of it. You only get one.

Win8 64-bit OS. Managed to...

Hello fellow techs

Does anyone know how to disable duplex copying on the BH601 series?

I looked for it on active solutions, and noticed something regarding DIPSW31-0 to enable advanced output...

Don't know how you do it, but Im a slim guy, so can go through the back and just take the plunger bit with the spring on out of the solenoid and replace with new.

Title
FS-535/FS-526 J72-19 or C1103


Language
English


Release date
2012-10-08

Sounds about right to me.

Two mylars deep within the finisher. Tech advice tells you to strip the finisher down to take them off. However, once you have found said tech advice and spotted the...

Hello ppl

I now have a wonderful job on my hands of fixing an overworked C10.

Original problem was transfer belt rotation error (I think). A colleague of mine booked a T-belt for it, and...

This customer was using 80g but is really cheap sh*t.

Update for any of you guys interested on this one.

There is now a tech bulletin out for KONICA MINOLTA AUTHORISED TECHNICAL PERSONNEL. Regarding this problem. You should be able to get it on...

Download file name]
4038-F000-GCV-K1-000.EXE
4038-F000-GCV-K1-005.EXE
PRI_DLBT0800566EN.doc


2. Where changed
Release of bizhubC252/C252P (Modified Phase 3.05)
The individual files inthe...

Shot in the dark here , but maybe try altering warm up time??

Thanks for the info folks

A colleague of mine went to have a look and stuck a whole new feed assy in. Still doing its J2002.

Customer is fairly happy feeding A3 from tray 1 so leaving it at...

I broke a brand spanking new punch kit on an install because I was having a bad day and got annoyed with it. Yanked it out of the machine and left half the wiring loom in the finisher. Lesson...

Yeh, there was a Sh*tload of paper dust on the take up sensor, but give it a good clean.

The customer is actually saying they preferred their C451. I nearly spat my coffee on her!! Ha ha...
...

Firmware?

Evening all,

Need a little help.

C554 jamming tray 2 A3 booklets J2002 codes. A3 runs fine from tray 1. Very low vol machine. Flashed V68 FW. Took out the feed assembly and stripped the clutch...

Check to make sure the correct toner is installed. I had exact same problem today, and the customer had stuck the wrong bottle in. The extra notches on the bottle were jamming in the bottle section.

That is the solution ID off Infohub

Enjoy

Vac out the cleaner section. Keeps it going for a while till the next time. A lot cheaper than changing the belt every time

What is the problem you are having with the C451?

Yellow laser unit. You will have to swap it out if the code wont clear with opening and closing the door, turning off and on etc.

Sorry for the delay.

Problem was a faulty tcr sensor onthe M IU. It was popping ICP 4 on prcb.

The lesson is - Fit new IU before any boards!