Search:

Having a unique issue here. Connecting the unit to a network with 8 users (simple network, no bells and whistles) I can ping the unit, and access the embedded web page, but cannot send print jobs. ...

No joy there either ... I guess I will just have to do it the hard way and pull the solenoid so I can rotate the shaft manually

I don't think one exists for that unit. Canon uses some pretty universal error codes and sometimes you can extrapolate from one unit to the next. I checked for a different model (further up the...

Usually E602 deals with external storage (Hard drive) ... I would try to remove any memory modules or other accessories from the formatter and try starting it up again. If that doesn't work then it...

... oh, and none of the usual suspects (ManualsParadise, justmanuals, nodevice, smpc) have even a sniff of the manuals.

I do have that manual and I have tried that procedure as best as possible given that the control panel is configured different. I am guessing that Canon decided to support this product as well as HP...

This unit is the mutant spawn cousin of the HP CM2320 and there is some procedure that has to be performed in a service, or secondary service menu to rotate the driveshaft to allow proper access to...

<Insert extremely vulgar and unbelievably inappropriate string of obscenities here>

New Formatter, no luck

Unit does not have removeable firmware

any suggestions?

BTW, I am out $2000 on...

I have found that print quality issues on these units are sometimes the result of fogged optics. There are two scanner assemblies in the printer and the one that is closest to the fuser is the one...

Well, when all is said and done I am stuck at Formatter, but I still can't figure out why the good formatter failed to work once it was reinstalled in the working unit.

Oh, and to make matters...

I am constantly changing out formatters on these units. I have about 10 units in the field and it seems like I am swapping out those boards annually.

Well, here is an update from the land where Rage reigns supreme.

Received the DC controller board and installed it in the one machine that was working until I put the non-working machine's...

Also, the unit will not process jobs sent over the network. Both units have the onboard NIC

Thanks, I have the service manual and have done the contrast thing as well. The touch display will flash briefly at power up and then remain dark, none of the LEDs cycle during the startup but all...

Hey Prntrfxr

Thus far I have done the following

remove and reseat formatter cage
remove and reseat cable to display and reseat on board
tested P/S to ensure 24V DC is steady
both units...

Looking for a little help here before my best client rips my naughty parts off and staples them to a wall.

Working on a CM6040 and had removed the formatter board in order to service some other...

I need the firmware because I had to replace the ADF DC Controller PCB. For reasons unknown it can read paper sizes when copying but when we go to fax, no matter how I change the setting in the...

As I said, I am looking for the firmware for an IR2270. Will purchase or trade for material I already have.

Assistance is appreciated, thanks in advance.

If you are being cranky about mooches that is one thing, personally I need firmware for a 2270 and I am willing to pay, but I can't find any site (including yours) that has it.

I have programmed the tray through the F5 menu to Ledger size. When we send a print job to the unit calling for Ledger paper it prints it no problem. When we place Ledger size paper on the flatbed,...

I got a screwball one here. When you place a Ledger size document on the scanner glass it will recognize it but even though the unit has the paper size in the tray, and it knows there is paper in...

Thanks for the advice ... I will check into that and let you know :)

Need to bounce a question off the group mind.

I have a 2270 that refuses to bring the paper up to PS10. I have recently replaced all the tray pickup rollers, the vertical path roller, and the...

This seems to be an error code specific to the scanner portion of the unit, but I can't find mention of this (or any other) 117-xxx errors in the manual.

Has anyone else ever seen this? If so,...

Okay, I will play with that and see how that works out. The root of the problem is installing an ethernet card into a unit that wasn't previously set up for it and getting the E246 error as a...