Can i get someone who has access to the Sharp AIP Connect program to get me the connectors for use with the Phoenix MX3070 machines? Thanks.
Type: Posts; User: repn1999
Can i get someone who has access to the Sharp AIP Connect program to get me the connectors for use with the Phoenix MX3070 machines? Thanks.
SO I would definitely do a FULL calibration on this as suggested. BEFORE you do it.....clean the density sensors....and run a dv refresh 44-17, then do 50-10 adj for the trays. NOT 50-28. if these...
I have a Sharp MX6050N machine in the field with a history of CPFD1_N jamming. Machine is outfitted with 3 tray desk plus the machine try for a total of 4, with a rb25 and saddle stitch finisher....
on some machines you can get it to scan color if you put a sheet of paper on top of the check. i believe the guideline is that it has to be plus or minus 20 percent in size if color to prevent...
be sure to check the screws on the ducts to make sure they are tight. that will cause a similar sound to a bad fan and you will end up ordering a fan for nothing. also for what its worth I would just...
this does use a jig. It is the same one as the 3501-5001 used. I am a factory trained tech on this model so I’ve seen it a lot lol probably more than I want to.
I agree with the post about new supplies. Another thing to check is are the density sensors clean and are there no scratches on the pri belt where the patches run that are looked at by the density...
Orange light means something is up with the dc power supply. Replace that. They are known to go bad. Same thing for cycling green orange light.
does anyone have a factory image for the msata card for a Sharp MXM3050 and a MXM3070? I would really appreciate it if someone could hook me up with them. I have a bunch of sd card and msata images...
They are brand new units from sharp and they have been tested in other machines where they work fine. Client runs health care type forms and no bleed to speak of just mostly bw text. Very rarely even...
So I have a mx3640 that continues to build toner and make the screeching noise like the web is locking up. I have confirmed that the client is not running machine out of spec or heavy coverage or...
replace the tray height sensors...i believe there are 3 and check the harness to the paper detect sensor on the tray. if the harness is not routed correctly it can get stretched and will cause that...
I just deleted some. Message me if you need to.
Dumb question....Did you happen to check the density on the print and copy settings and make sure they are on defaults? I had a tech who wouldnt change out supplies and reset the counters...and when...
I would recommend replacing the Mini EMMC (smaller MSATA) card. I have seen corruption issues on the new eMMC drives on most of the new models unfortunately and have replaced several. I would also...
I know the issue is resolved from a previous post...but I would strongly recommend replacing all sensors in the feed units ANY time you have an issue whether that sensor is effected or not. This is a...
I would say try a CN update with the latest version of firmware. IF this is an older MX6070 check the label on the MSATA drive on the MFPC PWB. IF the label says lower than v4.0 firmware I would...
I would say try swapping the dv unit. Your pic isnt the best but looks to me like lines/voids that match the surface of the dv unit are in the background. may have a dv unit rotation issue....I have...
I have them. I also have SD card images for this series. Please advise whether your machine has a data security kit on it or not. I need to know this before I provide any software so you dont end end...
Are you still looking for a Sharp tech? I would be willing to relocate for the right opportunity. I am factory trained and fully certified on all current models. I was also a master tech regional...
Excellent machine.....recognized among all manufacturers as a top performer and robust beast in the segment. Pretty technician friendly....stay up on the maintenance and you will be fine. My machines...
Like the other guys have said, these are older but built like tanks. All of the dragon series was...and now the newer taurus series (mxm754,mxm6750) continue the durability these machines were known...
does anyone have a kip 7100 wide format parts guide they can hook me up with? thanks in advance
[QUOTE=bigdaddyooo;1435100]
First I was addressing the comment someone made about swapping msata cards from another machine. Second....the reason you are having to CN update the cards is...
so this only happens on side 1. can you reproduce the same random position issue by scanning from platten glass, since side 1 is read from ccd. if so then that would rule out dspf mechanical and...