Search:

Type: Posts; User: acsolutions

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    2,656

    [Jamming] Re: c458 Jamming from tray 1 only

    those one way clutches slip on the shaft a lot. Pull the feed unit out and use fine sand paper or scotchbright to clean the shaft for the feed and the pickup rollers where the oneways sit.
  2. Replies
    22
    Views
    2,656

    [Jamming] Re: c458 Jamming from tray 1 only

    I took it back to the store and disassembled, scored the shaft, Cleaned and lubed the shaft and bearing, reassembled and installed in the machine I pulled the part from. I ran several hundred copies...
  3. Replies
    22
    Views
    2,656

    [Jamming] Re: c458 Jamming from tray 1 only

    The feed drive assembly worked. Thanks for all your assistance.
  4. Replies
    22
    Views
    2,656

    [Jamming] Re: c458 Jamming from tray 1 only

    I'm going to take a drive assembly out with me but if that doesn't work I'll check that out. The only thing that makes me hesitant is that it sometimes gets to the registration roller and sometimes...
  5. Replies
    22
    Views
    2,656

    [Jamming] Re: c458 Jamming from tray 1 only

    Basically the main drive drives tray1 and there are no clutches. I had a feeder assembly and swapped that out with same results. I guess the main drive is direct drive to tray.
  6. Replies
    22
    Views
    2,656

    [Jamming] Re: c458 Jamming from tray 1 only

    Yes,That's all part of the feed assembly.
  7. Replies
    22
    Views
    2,656

    [Jamming] c458 Jamming from tray 1 only

    Hello, I think I just need confirmation on my direction. Will feed from drawers 2 and 3 but when I try to feed from tray 1 it will feed a single sheet fine then jam everything else after. Sometimes...
  8. [Misc] Konica C368,cant print from windows 11 S Mode

    Hello, Cant find driver for C368, printing from windows 11 S mode. Any suggestions? Thanks
  9. [Misc] Re: scanning from IR advanced C5250 to windows 11 computer

    Thanks guys, for all the options. The machine is at my home and I'm having my
    wife scan to email until i select the option. Thanks again and I'll post when I get the scanning going.
  10. [Misc] Re: scanning from IR advanced C5250 to windows 11 computer

    Thanks, I was afraid of that! I have no way to get that firmware due to not being an authorized dealer. Is there a ftp utility I can use?
  11. [Misc] Re: scanning from IR advanced C5250 to windows 11 computer

    My windows 10 computer in not fixed and it works just fine. Yes, it does have a user name and password, you can't set it up without it.
  12. [Misc] Re: scanning from IR advanced C5250 to windows 11 computer

    What dont you understand. I can scan to windows 10 smb but not to windows 11 smb that's about the best I can describe it.
  13. [Misc] scanning from IR advanced C5250 to windows 11 computer

    Hello, I'm unable to scan to a windows 11 computer, I did set it up on a windows 10 computer. turned on smb and file and print sharing with firewall turned off, still says re sending then a tx...
  14. [Misc] Canon C5560i lll document feeder registration problems

    Hello, registration off about 10mm in feed direction.
    Cleaned roller and dusted off sensors to start with
    Then adjust doc stop in service mode to correct.
    When I place 1 sheet in feeder it's...
  15. Replies
    6
    Views
    1,071

    [Misc] Re: konica C458 message

    Here's the message.
  16. Replies
    6
    Views
    1,071

    [Misc] konica C458 message

    Hello, when copying and scanning from document feeder or on the glass I get a message "failed to complete job. Please check job history" it comes and goes. Some times after trying on glass or...
  17. Replies
    1
    Views
    931

    canon c5240a error code e227-0101

    Hello, error code relates to possible reader controller.
    Pulled out the meter and it's not functioning. I suspect power supply or relay b
    It also shows the front door is open. I will probably...
  18. Replies
    3
    Views
    1,027

    [CQ] m281 laser cleaning

    Hello, my m281is printing very light all colors. All supplies are at 90% and the image on the transfer belt is very weak. I removed the toner tray and tried cleaning the laser glass through the...
  19. Replies
    12
    Views
    9,095

    [Jamming] Re: C754e jam code 1102

    It will feed 2 or three sheets before it jams. It gets to the registration roller. I cleaned the pre regular sensor and cleaned the dust collector
  20. Replies
    12
    Views
    9,095

    [Jamming] Re: C754e jam code 1102

    The customer said they have another machine I can swap out the unit but I have to wait to return fro vacation.
  21. Replies
    12
    Views
    9,095

    [Jamming] Re: C754e jam code 1102

    Thanks, yeah I stuffed the shaft but did not change out the one way. Thanks
  22. Replies
    12
    Views
    9,095

    [Jamming] Re: C754e jam code 1102

    Rollers have been replaced and feeds fine through all the trays. I'm thinking about replacing the clutches in that port unless someone has any better ideas. I also tried registration loop adjustment...
  23. Replies
    12
    Views
    9,095

    [Jamming] Re: C754e jam code 1102

    Its happening in tray 1 only. No error code jam code only.
    Machine comes to ready and will run 1 or 2 copies then jams.
    There's about 750k on machine.
    Its jamming right before the registration...
  24. Replies
    12
    Views
    9,095

    [Jamming] C754e jam code 1102

    Replaced pickup , feed and separation rollers. Cleaned sensors, pulled one way clutch off and cleaned clutch and shaft. Still jamming. Thanks
  25. Replies
    4
    Views
    1,923

    [CQ] Re: mx4111n light black copies

    Awesome bill thanks my friend
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4