The k drum phase sensor is a good one If you have never seen it, it will give you fits. Blackcat nailed it. There is a pub on it from the first generation series.
Type: Posts; User: android790
The k drum phase sensor is a good one If you have never seen it, it will give you fits. Blackcat nailed it. There is a pub on it from the first generation series.
Find k-base june 2,2003. In short, u may have a short. Open front door/halt normal warm up sequence. Perform error clear. With door open and/or transport unit out (just so it dosnt come to ready,...
thats the one. thank you for that link. explains much more.
good machine, but as mrfixit51 said, it is not a CLC. see if you can demo the machine for a day or so to check out your image reproduction. if you cant, gather up samples of what you do and test it...
if this is the series of machine i am thinking of, there is a mod/on newer machine, a bottom plate that is not fixed, but can move a little. it gives you a little more space away from the belt. if...
try SNMP unchecked in properties part of driver. its under the ports tab.
This is just a case of a non tech trying to reset the thermal fuse without the proper training. I keep telling them to remove the fuser first. Wish they would read first, then fix.
At the right side door, when open, in the lower left corner, a screw will strip out of the frame causing the pressure to be off.u may have to take off the door to see it. There may be an old tech pub...
I was going to say it is nice to know I am not alone in my maladies, but you hate to see others old beyond there years too. I keep a cane in my car so when my knee goes out I can wrap it and finish...
I have had to replace the hinge plate for the wave more than once. It looks fine,but has some drag. I had to rpl fixing belts (rare). The 010b, I have seen: paper still in the finisher.deflector...
if they would have posted this on the rant,rave,and everything else, i may have responded. it was posted on the canon forum. i know it was machine related, but it was a more of a rant, and that is...
Best guess is the drum blade flipped and locked the drum unit up. Or, the drum motor bad, or the transfer belt assy broke/torn/displaced. Easy check is to install a new drum, or put that drum in a...
I did not see much on this code. It said... TS1 toner sensor shorting out, but this should have been replaced with the developer tank. Scraper for the sensor,but also replaced with tank. U replaced...
Your right. I went off the code only. My bad.with the crackberry I use, the sample images either don't load, or takes forever. I will have to skip posting if samples are shown and I can't view.
Some things to consider. Replace toner cartridge drive assembly (FM2-5363-000) for yellow if toner is not being supplied. Your code is a toner density ratio off. You might have ATR sensor related...
Teckat is right. Before you do anything else, put an origional on the glass,close the lid and make a copy. Does it have lines? If it dosnt, you have a dirty doc feeder read glass. Do this and let us...
First, reinsert the drum you just put in and run some prints. But, it sounds like the cleaning blade for the drum flipped. I would put another drum in, and if it has no lines, you can turn in the bad...
You should relook at what teckat and others posted. Your answer is there. I have been following these people for a while, and I have found that 1) you misunderstood what they were saying. Or 2) it...
Check PS12. PO25-bit 7. In dc-con I/O. 1 is paper present,0 no paper. This is the sensor to right of transfer roller. If good, check its spring,if on add a wrap. This is found in the service mode....
Sugar glazed doughnut in df, christmas fruit tray (found in june) in sorter, candy wrappers, a white tube sock, bugs of all sorts, broken jewelry, paper and coin cash, tools, lists of all sorts, and...
The IR1610F can fax, 1600 won't. My bias creeps in with the service mode this unit has. Anything like this, in my mind is a fax machine that copies. I place the IR2020 as a fax machine. I am sorry if...
I am not a fan of this unit because it is a fax machine that wants to be a copier. Having said that, I have had only a few, want to take it to the trash moments, problems. If you work it easy, feed...
E-732. Reader communication error. Check to see if the reader unit is unplugged. I had machines shipped without this cable. That is easy to check if missing or loose. Also: reader pcb, sub controller...
I got to go with a service call to. Any work you do to the machine other than paper/toner change will void your warranty.
Our parts department buys the film only, with a small amount of grease with it. So far, no problems. It may come from katun. I had some grease left over. You should find something like that if it is...