Search:

Hello guy's,

We have a quality problem with C.6501 . The engine has 1900K.

You can see the problem on PDF.

Problem description.

Problem is only on Magenta color at rear machine, on...

Yes, the units worked with the main body during 4 years , we got the problem after repair for error C.C101.

Thanks for your help,

Twinax

Hello,

This problem (fine black lines on print) are a complexe problem. (residual electrical charge has been developed after cleaning)

The original cause is the DU102C drum which have a very...

Hello Guy's,

We have a C6501 who got an error C.C101, all known causes has been checked and repaired. (clutches, short-circuit, PRCB...).

Now ,the engine works well but alone (without...

Hello Zolraldinho,

Many thanks for your help,

After investigation on field I saw that the black color was too early on print (PG Type 10) and cause the error code E194.

The problem has been...

The product range is higher.

Twinax

Hello everybody

In which direction do you have the lines?

KM send the Old drum DU102C modified with a high pressure on cleaning blade. It is necessary to have the firmaware rel.70 and patch...

Hello,

I know perfectly those engines, each engine have positive and negative points.

First question is about the montly print volume, untill 150K/Month the KM works well but not much. the...

Thank you,

ITB and color sensor has been replaced without success !

Is there possible to check the patch on ITB?

I think that the patch have problem and can not be read!

What did you do...

Hello guys,

We have an error code E194 -0061 and 0071 on IPC 7010, we are unable to do the auto correction color alignement which give E194. color on page are mixed (black into magenta).

The PG...

Hello Italo,

Is your problem on one side of duplex printing or also on single side?

Most of time this problem is caused by the CCD registration which is dusty (not clean), when bypass is used,...

Hello Italo,

Most of time the PRCB pba goes down due to short circuit.


Change PRCB.

Your English is not worst than my ! (I'm French ;-)
:cool:
Twinax

Hi,

You can directly go to service mode, press "counters/ utility" then switch on the engine. Let a front door open can be also a solution.

When all colors are involved the problem is very...

Hello,

This is a known problem. The problem is the thinkness of paper (in combination with internal compoments), the maximum is 340µm for 300 gsm. (Problem from 300µm)

There is also the paper...

Hello,

You are right about the screen selection (DOT1 or DOT2) but I already got this kind of problem.

Solution was to clean the glass on laser unit x4 (only outside glass) nothing was visible...

Hello,

Maybe hier !


Search for Answers.

Kind regards,

Twinax

Hello,

Ok, with which engine ?

Regards,

Twinax

Hello,

It is possible that with a wrong action you destroy a part of software.

That's not a problem, try to connect SST via (star 1 & 7 star) instead of *2&8* you got a fix IP from engine, you...

Hello,

Unfortunately, all points has been checked several times without any result.

Main-P, main-M ,all DC-Con has been changed, also 3 x cables between DC-Con and Main-P.

We have noticed...

Hello,

The best way to print PDF is Acrobat reader or the top acrobat Pro. Other software are emulation.

PDF files are sometimes complexes, it is not a good way to print pdf file in PCL !...

Hello,

The error code C-C101 is software error.

You installed a new PRCB, this one is delivered with a basic software in version 11, you need to upgrade your engine in lastest version...

Hello,

Situation become catastrophic... 15 days after installation engine still locked by error code E733.

Several PCB has been replaced: DC-Con1-1 , 1-2 , 1-3, tranceiver PCB, main _M PCB,...

Hi,

I will check it tomorow (monday).

And keep you informed.

Have a nice sunday.

Regards,

Hello,

It also arrive very often if the software version are not correct.

Engine version too old (e.g. when you install a new PRCB the version delivered is 11, if the version was 60 on previous...

Hi guys,

We are installing an imagePRESS C.6010 + creo. Engine works but very (too) often engine stops with error code E733-0001 (communication problem) a lot of connections has been checked.
...