Getting a 11:10 code. Overseas for the military and trying to clear this code. Not familiar with wide format printers but work on copiers and printers. Don’t have access to much. Tried googling error...
Type: Posts; User: otuvak
Getting a 11:10 code. Overseas for the military and trying to clear this code. Not familiar with wide format printers but work on copiers and printers. Don’t have access to much. Tried googling error...
Have above model that functions correctly except the read out after confirmation page says 0 every time. The fax's are all sent and received fine. If web into the interface it reads correct amount...
Thanks for the tip! That is what it ended up being. The serial number to the DV unit fell into the bad/problem category. Replaced and haven't seen the problem since. Thanks again.
I initially had this problem and swapped the Fiery cable and printed the SAME job and problem went away for about a week. Next, we had this same problem and reseating cables, Fiery calibration, all...
Does anyone know does canon publish most used parts per machine anywhere? Trying to make a inventory? Didn't see anything in ISG. Thanks
Looking for some advice. Noticed after doing 2-2 copies machine jammed. Clear jam and machine will show no jams but will not come to ready. Have to shut off and on with side switch. Machine will be...
Having an issue with this machine and wondering if anyone else has seen this problem. Jam history shows J83s and customer says its happening when they print from there computer. They currently have a...
Getting some j60's on this machine. Can never duplicate while I am there. It has the hang on finisher(fs-350). The only thing I am seeing is the finisher opens tough from the machine. Thanks for...
I have a call on Monday on this machine and looking for some ideas. They say after it sits for a long period ie on Monday morning the machine will not wake up to print and they have power machine off...
It was the memory! Thanks everyone!
Looking for second opinion on this call I had today. Getting what I call are some bar code like images when using doc feed or off the glass. Internal prints are fine. These lines seem to be in same...
Does anyone know the envelopes per minute specs or where they can be found? Checked hp web site and manual and coming up with blanks! Salesman sold machine saying its a little slower per minute. It...
I just had same thing today and had to replace touch panel. I found out that the touch panel is the same for many lines. I took one off a 3570.. Just an idea! Good luck!
What have you done so far? Have you tried firmware, different fuser, toner or tried throwing a manual at it?
Thanks for the responses! Found it to be the spring in pick up arm assembly. When paper was feeding it was bouncing and sticking in the up position and not pulling paper out of the tray! I can put...
Thanks for reading on a sat morning! If we are talking about same solnoid(one attached to pick-up drive assembly) I have replaced that one and pick up drive assembly with no change. The only thing I...
There is no paper jammed. Open and close top cover and it will print few more pages and jam. The machine seems like it slows down right before it jams.
Having a problem with this machine. History was showing 13.1 and 13. 2 jams. When i got the call I was thinking feed tires. Test run machine and it is jamming out of tray 2. No paper is jammed....
We had similar issue on a 3501. Another tech ends up replacing power supply.
New to Canon and having problem with double sheet feeding. It doesn't do it everytime but has been an ongoing problem. Replaced feed tires and sep pad(DADF-P2). I am not finding anything on canons...
Have a customer that just started using adobe-x. They will put notes and highlight them and they also will have names on the paper with a red line to indicate something. When they go to print it...
Thanks for the reply. Next time I am there I will give this a try.
Getting intermittent error at a customer’s office of it saying Bin 2 is full of an 8 bin mail box (Q5693A). I cannot duplicate this problem when I am there. The only other thing that I have noticed...
I am interested in the f6-17 route. Never changed this setting before. Won't see this machine for two months( hopefully).
If you are using win 7 to do firmware via FTP it times out giving an error. I use easy firmware update tool. Just thought I would throw that out there. Don't know if that helps. Good luck.