Search:

Type: Posts; User: MOSSY BOY

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,208

    [Error Code] Intermittent SC 204 on Ricoh MP301

    HI Guys,

    I have a MP 301 displaying SC 204 Polygon Motor Error after 30 - 40 prints.
    The device has approx 190K on clock.
    Print quality perfect until just before SC displayed, then half an image...
  2. Replies
    11
    Views
    8,516

    [Error Code] Re: New MP301's and SC202/204

    Cheers Polarbear, yep that's the only loom type thing I can see. I have checked and thoroughly cleaned the grounding plates in the area you are referring to. I have a Polygon motor PCB & Door...
  3. Replies
    11
    Views
    8,516

    [Error Code] Re: New MP301's and SC202/204

    Thanks Phil B, I knew it was a long shot, it was just another option for me to look into trying to resolve this issue on a device at the moment.
  4. Replies
    11
    Views
    8,516

    [Error Code] Re: New MP301's and SC202/204

    Niceville318,. Can you be more specific on which ground wire are you referring to???, as I have a MP 301 with SC 204 occurring intermittently. Thanjs in advance.
  5. Replies
    7
    Views
    2,971

    Re: @remote server gui login issues

    Hi drwevil,

    Are you referring to an @Remote Basil box (100 device) ?

    Install and use Firefox to access the GUI.

    I had the same issue with IE 11.

    Hope this helps.:)
  6. Re: Ricoh MPC-2050 not connected in the network

    Try reseting network port settings. Set Network security settings to level "0" in Administrator settings.
  7. Re: Mp 2250b works with everything except web monitor

    Try adjusting Security settings .....

    User Tools , Admin tools, System settings, Network security Level, to " 0 \ Zero"

    This should clear \ open all ports within Network Security.

    Hopefully...
  8. Replies
    11
    Views
    2,147

    [Jamming] Re: mpc2800 fuser jams full colour only!!

    Is location 19 that the log is showing the jams ??

    I asume that the H & P rollers etc, are in a "good"condition?

    Try SP modes listed below, it seems to work for me.

    Remember to reboot the...
  9. Web image monitor not showing in browser

    Hi all,

    I have an issue with a MPC 7501 WIM not showing when the address is input into a browser.
    There has been no configuration been carried out previously to cause this.

    In Smart Device...
  10. Replies
    12
    Views
    6,219

    Re: MPC 5000 Fusing issue

    Just some things to try, and think about

    Looks very like insufficient / uneven pressure.

    Is it only happening at the rear or the front of the device.?

    There is a motor that engages tha...
  11. Replies
    14
    Views
    12,365

    Re: MPc4000 Please Wait and SC636-01

    Hi Llama God

    When you say freezing, is this when selecting the login (CAP) screen, or when you select Prints (ELP-NX), or is it when you release a print job?

    If the screen is freezing /...
  12. Replies
    14
    Views
    12,365

    Re: MPc4000 Please Wait and SC636-01

    Hi Llama God.

    See below.

    SC 636-01- Expanded authentication module error
    Posted Mar 15, 2010 3:17 PM


    [Symptom]
    SC 636-01- Expanded authentication module error
  13. Replies
    4
    Views
    2,474

    Re: Eror code SC672 MP2510

    Hi, if this device has a HDD on it take it off or just disconnect it.
    try booting up m/c and if ok then your HDD needs formatting, if not its a new controller pwb.
    If a format is required,this can...
  14. Replies
    10
    Views
    4,158

    [Jamming] Re: MPC2800 jams at locations 19 & 20.

    Hi Guys,

    Thank you all for your responces so far.

    I was back at the device on Monday, 4 jams logged at 19. Again unable to fault on testing.

    Changed the fusing exit sensor, reduced fusing...
  15. Replies
    10
    Views
    4,158

    [Jamming] MPC2800 jams at locations 19 & 20.

    Hi Guys,

    I have got a Friday afternoon machine that is starting to really frustrate me.

    I am a site engineer looking after 50+ devices, (10 x MPC2800) and the last four Friday afternoons a call...
  16. Replies
    2
    Views
    9,090

    Re: Enhanced Locked Print NX - error J522

    Hi,

    Have you done what Choro1dal suggests?,

    If you have installed and stored the licence using remote Manager there should be no issue.

    I have found that if you try to start ELPNX you get...
Results 1 to 16 of 16