Search:

Type: Posts; User: ricoh

Search: Search took 0.01 seconds.

  1. Thread: Practical jokes.

    by ricoh
    Replies
    22
    Views
    2,932

    [Funny] Re: Practical jokes.

    1/ A thin smear of conductive grease or toner on the eyepiece of a loupe.
    2/ Grab your colleagues spare key when they are on lunch and with a paintbrush and a small amount of black toner, apply to...
  2. Replies
    9
    Views
    1,899

    [Video] Re: The worst copier commercial ever

    I've seen worse...

    www.youtube.com/watch?v=Aq5aFVjzKs8
  3. Replies
    15
    Views
    2,207

    Re: Toolbag suggestion

    The Drag Bag has been a tried and tested favourite. Big wheels, lots of space and a long curved handle. can be used as a backpack too and is very comfortable. the only downside is there are no tool...
  4. Replies
    2
    Views
    570

    [CQ] Re: Pro C5100 - 1st side magnification issue

    Hi Starion,
    The simple answer is yes. I assume this is happening on a particular stock that is suffering heat shrink. In this case there is the option to alter the setting for this paper in the...
  5. Replies
    24
    Views
    11,359

    [Error Code] Re: 1357ex Pro - Constant Functional Problems (SC495)

    This issue is usually sorted by cleaning the toner lines and cylinder completely, being careful not to damage the toner detect sensors with static. Then replace the short section of tube from the...
  6. Thread: MPC-7500

    by ricoh
    Replies
    24
    Views
    4,635

    Re: MPC-7500

    Bingo, I think you are on the right track. Ozone contamination is usually the cause of this issue, and as the K unit is the only one that has a charge corona, it will usually always be the problem...
  7. Replies
    4
    Views
    979

    Re: Ricoh Pro C700ex ripping fuser belts

    Hi Javaman,
    It might be worthwhile ensuring the fuser entry plate is screwed at the default centre screws at either side. Also that the belt tension roller is set to the default centre location. If...
  8. Replies
    27
    Views
    7,221

    Re: MPC6502 / 8002 - Insider info?

    The replacement for these will be the same speeds. Although, rumour has it Japan tested the new "baron" series successfully to 250ppm:eek:. We won't be seeing that speed though unfortunately (?).
  9. Replies
    27
    Views
    7,221

    Re: MPC6502 / 8002 - Insider info?

    I can't imagine anyone outside of technicians in the real world replacing, for instance, the fuser unit. Even the PCU's will not be swapped by the customer with the exception of the over-zealous...
  10. Replies
    7
    Views
    2,139

    Re: 1357ex Pro Faint prints

    Check your VSP reading in SP 3-103-003. it should be 0.5v +/- 0.2v. over the reading will indicate that the developer is starved of toner. 5.00v could indicate a U/S TD sensor.
    Ensure toner is...
  11. Replies
    27
    Views
    7,221

    Re: MPC6502 / 8002 - Insider info?

    D135/136 for office range
    D137/138 for Pro range.
  12. Thread: MPC 7500 w-sc870

    by ricoh
    Replies
    4
    Views
    646

    Re: MPC 7500 w-sc870

    Hi T911

    Due to these devices using a unique proprietary RAID format, all HDD's must be replaced at the same time.

    Enjoy.
  13. Replies
    11
    Views
    1,897

    Re: riso gr3770 drums over inking in centre

    It will most likely be the seal attached to the trail edge of the drum body. The glue perishes after a while allowing ink through. Outside of that, I would be pulling the drum down and re-tapping...
  14. Replies
    20
    Views
    1,632

    [CQ] Re: mp9001 backgrounding

    I'm surprised you successfully cleaned the potential sensor. Those things don't usually like the look of a vacuum or a brush.
    I was going to suggest on this the transfer belt also has a knack of...
Results 1 to 14 of 14