Search:

Type: Posts; User: eg101

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Goodby

    by eg101
    Replies
    7
    Views
    1,125

    [Misc] Goodby

    After over 40 years clearing paper jams I am retireing and I just wanted to tell my fellow Techs how much I have appreciated the help they have been.
    Also I thank the organizers for this site for...
  2. Thread: Fuser exit jam.

    by eg101
    Replies
    8
    Views
    1,178

    Re: Fuser exit jam.

    Did you record the model and S N in the copier?
  3. Replies
    10
    Views
    4,273

    Re: Biz 223 false misfeeds tray 1 only.

    Thanks for all the help. Turns out the bushings on the timing rollers were bad.
    Go figure
  4. Replies
    10
    Views
    4,273

    Re: Biz 223 false misfeeds tray 1 only.

    Thanks for the suggestion. Tried it, got 1 sheet through, jams again.
  5. Replies
    10
    Views
    4,273

    Re: Biz 223 false misfeeds tray 1 only.

    I cannot find actuator or sensor at paper exit area of feed unit.
    I compared feed unit with one from Biz 423 and they are different. 423 feed section has 3 photo interrupters and Biz 223 only has...
  6. Replies
    10
    Views
    4,273

    Re: Biz 223 false misfeeds tray 1 only.

    Thanks. I tried SSD site but didn't find anything about false jams, maybe I just missed it.
    It's really puzzling since it all looks so right
  7. Replies
    10
    Views
    4,273

    Biz 223 false misfeeds tray 1 only.

    Have Biz 223 in shop for other repairs.
    When testing machine after major repairs discovered that it displayed paper jam only from tray 1, other trays work fine. I have replaced feed rollers and O/W...
  8. Replies
    11
    Views
    6,172

    Re: C1070 static problem

    Tape a piece of Bounce in the exit area
  9. [Misc] Re: Bizhub C203, Cannot open the copier in browser by typing its IP Address.

    Since you're in Australia, you might have to type the IP address upside down..LOL[/QUOTE]

    Naah, they're standing upside down anyway.
  10. Replies
    7
    Views
    6,421

    Re: 3200 error code, what is it?

    Scanner was unlocked, it didn't make the LOUD rattling noise when you forget.
  11. Replies
    7
    Views
    6,421

    Re: 3200 error code, what is it?

    Doc feeder was in a bind. Machine worked o k with doc feeder open, threw error code when closed.
    Took feeder off and re-seated - works.
    Go Figure.
  12. Replies
    7
    Views
    6,421

    Re: 3200 error code, what is it?

    Thanks. Found it!
  13. Replies
    7
    Views
    6,421

    3200 error code, what is it?

    Setting up a new FS-3640. After warm up 3200 shows in the screen with instructions to turn off and on. Done that 10 times with no effect. I work for a dealer but normally on Konica Minolta copiers....
  14. Re: Konica Minolta 250 Orignal 220 Power. ADF Copy Error

    Is the scanner lock on?
  15. Thread: Bizhub 350

    by eg101
    Replies
    8
    Views
    1,424

    Re: Bizhub 350

    I've had the actuator on the reversing unit come loose.
  16. Replies
    21
    Views
    3,930

    Re: bizhub 250 can not perform f-8

    Yes, t
    the DI 2010 series uses a smaller package of
    developer than the Biz 250 series.
  17. Replies
    4
    Views
    1,998

    Re: MFX 3530 main P C Board

    Poor trace to analog counter. When I plugged in the harness the trace came loose from the board
  18. Replies
    9
    Views
    806

    [Jamming] Re: 7022 crumpled page on 2 side print/copy

    It's either your paper or the fuser. Try a new ream of paper first.
  19. Replies
    4
    Views
    1,998

    Re: MFX 3530 main P C Board

    Never mind.............. Tech support came through already! Got the P N>
  20. Replies
    4
    Views
    1,998

    MFX 3530 main P C Board

    Have a new 3530 that needs a main control board. Muratec dealer site doesn't show parts for this model.
    HELP!
  21. Re: Bizhub pro 920 print quality fading on edge of paper

    Looks like laser problem. You sure the glass is clean.
  22. Replies
    2
    Views
    1,421

    Re: Set fax as default

    Not for all models but here goes.
    Setting, star04, switch edit, 070, 3rd diget from right change from 0 to 1, enter, reset.

    Switch 70 selects default choice. 0 for Copy, 1 for Fax.
  23. Replies
    4
    Views
    1,232

    Re: 223 Replenish Paper

    You did check for paper left in the machine behind the tray didn't you?
  24. Replies
    4
    Views
    676

    Re: KM350/Ineo 350 sandy output

    It's likely a fuser problem. Toner not pressed into the paper.
  25. Replies
    7
    Views
    2,070

    Re: SERVICE ERROR P-21

    PLEEZE, change your avatar. It looks too much like my 2nd wife! PLEEZE.
Results 1 to 25 of 135
Page 1 of 6 1 2 3 4