Search:

Hi.
Was there any solution to this problem at the end?
Thanks

Did you try with the correct Laser since then? It's very strange. Unless it's a wiring problem there must be an electronic part which is faulty. When i saw the picture i just thought this is either...

C253 the FW would be A02E0Y0-F000-GXH-R6 in your case. As you see it's based on R6 but special for boot problem from MFPB. Also, have you any spare NVRAM only for test purposes?

If you don't have the special FW try the mass production. With both it can't be worse than now! Don't worry. In worst case you will have the same problem as before. But important is to see if the MFP...

Yes it is for this model too. These are the supported types: C451/C550/C650/C203/C253/C353. But each one has a different FW of course. This doesn't mean, that this works in all cases but let's say...

Before NVRAM recovery i would try the special FW for "sandglas". If it doesn't work then you can go for the NVRAM Recovery. Also before all that try to disconnect the HDD and see if it is the same.

Well then it sounds like MFPB problem. You know there is a special FW for this issue. If you hava access to the CSES then search for "sandglas".

14642

I think it's a PWB-M problem. Try to reflash the machine and see what happens.

Was the M1 motor changed before that? Check the ICPs fuses on PWB-SIF. Have you tried to reload the FW? Check also PJ7 on DCPS.

If you have tried all these steps then it can only be the MFPB. I guess if you start the machine now you see only the sand glass on the display and machine will not boot any further. But again....

I think the Japan earthquake problem is referring on scanner FW and not MFPB FW on these models. It's only Scanner FW which deffers. So in your case first of all i would suggest you to use an other...

The info i provided was based on these documents and my experiences on C250/C252. But in your case if you have tried the PSU on an other machine and it produced the same error then it means that is...

Just in case. Sorry for the question but did you exchange the correct motor (M10) on the right door assy? If yes it is strange because the control signal for the motor is coming from motor control...

We had exactly such a case couple of months ago with a BH 250 S/W which is almost the same mashine (MFPB same). Tried everything possible from our side. Nothing helped. At the end an other mashine of...

I have a used MFPB A02EH34106 C353 for sale. If you are interested PM me.

We are talking about cases where NVRAM must be exchanged because of a problem (C-dxx, i-Options, etc errors). I think no tech is happy if he has to exchange it (licence error and configuration).

If the counter is so important for KM i would except a NVRAM tool to recover the counter if one has to exchange the NVRAM. And what about a recovery tool for the NVRAM for Amur/Donau like the one for...

Yes in case of warming up message this is correct. I thought that the machine doesn't even come so far in his case.

BH 601/751 have only one CF card. BH 600/750 have 2. One on the IPB and one on the CB.

Hello

If i am right the problem with these machines was always the CF card on the SCB and not the one which you can easily take out from the side of the machine on the IPB. An other possibility...

This is wrong. The right one is Suction fan motor M10 (9313 1000 72) 11925

I would try an other control panel to see if the problem comes from there. Otherwise it could have a relation with the error you mentioned before C-F023. If you have a C250,C352,C351 all these panels...

C-F023 could be following.

-RAMs on PWB-ES Board.
-Old FW Version.
-Connection problem.
-PWB MC
-PWB MFP.

I would suggest you to make a memory check in "state confirmation" and upgrade the...

If you take out the transfer belt with all IUs installed try to move manually with your hand the white gear which moves the transfer belt. You should try both directions. Then if it's blocked try to...