Search:

Type: Posts; User: Dutchman

Page 1 of 3 1 2 3

Search: Search took 0.03 seconds.

  1. Kyocera KM-7551CI Concertina's at Register stop rollers when copying in colour.

    I am a bit baffled, the 7551 Was reported as jamming. I tested the machine and found that it works 100% when doing black & white copies or prints from all trays including A3 and A4r landscape and...
  2. Replies
    0
    Views
    6,219

    [Electrical] Canon Laserbase MF5770

    I have a Laserbase MF5770 that switches on without error how ever the LCD is blank no info displayed. Would this be a display fault or is it a board fault.
    Any help would be appreciated.
  3. Replies
    6
    Views
    2,052

    [Error Code] Re: IRAC2030 E020-1160

    I have had this a view times as well. Have normally replaced the drum causing the problem again and that normally solved the problem. Make sure that the patch sensor is clean. Apparently they say...
  4. Replies
    5
    Views
    683

    Re: Big problem!!!

    The inside of your drum developing area the P-Kit is dirty and causes the machine to arc. you need to take out all the developers and vac out the area especially the dev that has dropped to the...
  5. Replies
    1
    Views
    472

    Re: iR 5030 - Edit Fusing Temp.?

    Dear colleague,

    Herewith attached a PDF that will assist.30170
  6. Replies
    3
    Views
    551

    [Misc] Re: Image quality within our C1+ (band)

    Banding on a C1 normally comes from a gear or drive that creates the judder. I would check the following:
    1) Fuser drive gears, 2) drum and developer drive at the back behind the flywheel, 3) ITB...
  7. Replies
    5
    Views
    1,221

    Re: Ir3035 jamming in the fuser area.

    Check the dail on the paper tray if that is set correctly with the paper used in that tray.
  8. [Misc] Re: Canon IR5075; I cannot access Additional Function in control panel;

    Strip and clean or chance the switches on the keyboard circuit board.
  9. Re: Canon Advance C9075 error E004-0101, please help me

    Be sure to clear the error in service mode: Copier - Function - Clear - Error
  10. Employment wanted in Denia/Javea Spain mainland

    My wife and I are wanting to relocate to Denia/Javea Spain mainland.

    I am looking for a service engineer full time or part time position in the Denia/Javea mainland Spain and I am prepared to...
  11. Replies
    2
    Views
    676

    [Misc] Re: Calibration within Canon IP C1+

    If the calibration passed then I would not worry about the lower reading on the yellow. If you want the yellow to be more in line with the other colours then I would add toner in service mode and...
  12. Replies
    2
    Views
    541

    Re: IR C4080 ADF JAM

    Hi,

    Try the (sens-init) function in service mode selecting the feeder then function - Sens-init.
  13. Replies
    2
    Views
    1,018

    Re: imagePRESS C1 color Network Configuration

    Hi,

    If your machine is without a fiery then you would do the setup by using additional functions and go to network settings, If you C1 has a fiery then use setup on the fiery to alter the network...
  14. Thread: IRC 2105

    by Dutchman
    Replies
    2
    Views
    544

    Re: IRC 2105

    Thats right Zoraldinho E805 is fan related. Either exhaust fan or cleaner fan.
  15. Replies
    6
    Views
    3,717

    [Jamming] Re: canon IR2200 jam code 0105

    I would stip the pickup assembly and check if all is ok. Are you using FF5-4552 for pickup and feed and FF5-4634 or FC6-6661 for sep.
  16. Replies
    6
    Views
    3,717

    [Jamming] Re: canon IR2200 jam code 0105

    You might have a faulty clutch on the paperfeed drive system, if not then replace the pickup assembly
  17. Re: Message "preparing toner" during installation on iRADVC 5235

    Does the machine copy at all, If it does print or copy do a p-print and clear the DC controller in service mode. That should clear the problem.
  18. Replies
    10
    Views
    1,497

    Re: Service Level Modes2&3 on a Canon irc5030

    If there is a problem with one of the PCB's the machine will error and will show a error code. With that error code a person can rectify the problem.
  19. Thread: Yellow streak

    by Dutchman
    Replies
    3
    Views
    630

    Re: Yellow streak

    Glad its fixed. thanks for your reply
  20. Thread: Yellow streak

    by Dutchman
    Replies
    3
    Views
    630

    Re: Yellow streak

    Hi Thadwald, There are a couple of things that could cause blank areas. Check and see if the developer is evenly spread across the dev. roller sometimes there is hard toner just before the doctor...
  21. Re: Xerox Dc 250 Fuser error, Won't allow me to reset the NVM to 0.

    Thanks Have done: Now sorted:)
  22. Xerox Dc 250 Fuser error, Won't allow me to reset the NVM to 0.

    Hi, I am attending to a Xerox Dc250 with a fuser error. I replaced the fuser unit with another good used unit and tried to reset 744 156 in the NVM to 0 but it won't accept the reset. The present...
  23. Replies
    3
    Views
    913

    Re: problem canon IR2830

    Hi, Are you sure the Error is E761 and not E716. :confused:

    Errors E7XX is normally a communication problem with a peripheral or other unit with machine.
  24. Replies
    3
    Views
    1,276

    Re: IR8095 1011 jam

    Herewith some more info regarding why the parts were modified
  25. Thread: e00225 0001

    by Dutchman
    Replies
    5
    Views
    4,271

    [Error Code] Re: e00225 0001

    Item 9:
    Part number FM2-4354-010
Results 1 to 25 of 58
Page 1 of 3 1 2 3