Search:

Type: Posts; User: cobiray

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    10
    Views
    10,175

    Re: Konica 7165/7155 Developer Dumping Solution

    13876

    Here you go...
  2. Replies
    7
    Views
    1,325

    Re: Pro 907 with SR5020 stapler jogger issue

    Sorry, I get punchy sometimes if I don't have coffee in the morning...:D
  3. Replies
    7
    Views
    1,325

    Re: Pro 907 with SR5020 stapler jogger issue

    ...
  4. Replies
    7
    Views
    1,325

    Re: Pro 907 with SR5020 stapler jogger issue

    From the SR5020 parts manual it's on page 30 or figure 15. The motor is item 20 and the PN is B8305565, description is Stepper Motor DC6.7V 16W.

    I replaced both of the motors since they were so...
  5. Replies
    7
    Views
    1,325

    Pro 907 with SR5020 stapler jogger issue

    I've got a customer with a print shop that is having an issue with the stapler jogger in a SR5020 attached to a Pro 907. The first few sets are fine but as the machine runs the stapled sets, it...
  6. Thread: AF 2090

    by cobiray
    Replies
    1
    Views
    773

    Re: AF 2090

    SP5853 is the mode for loading the stamp data. Searching the manual the E32 shows as a firmware upload error. Are you attempting to do the stamp upload?
  7. Replies
    5
    Views
    4,099

    Re: Could not find valid licenced hardware

    It sounds like the board may have failed in the Plotbase PC. You can power it down and re-seat the card in the PC to see if it resolves the issue. If this doesn't resolve it you will likely have to...
  8. Re: ricoh 3245c-error-development unit(cyan) not set

    Apparently I'm not reading very well today....

    Check the brace that holds the units in on the front. It may be allowing the units to "walk" out of the unit. I've replaced a few of these in the...
  9. Re: ricoh 3245c-error-development unit(cyan) not set

    Start by re seating the connectors on the developer units. Sometimes these can be loosely connected when the units are replaced or disassembled. If you are using the black unit mod on the color...
  10. Replies
    6
    Views
    5,968

    [Error Code] Re: Plockmatic SR 90 BM-156

    Yes, each of the white connectors needs a jumper (VRC61134 - Interlock Jumper). Also, each of the cf90 or tr90 connectors above the white connectors will need terminators if they don't have them. It...
  11. Replies
    6
    Views
    5,968

    [Error Code] Re: Plockmatic SR 90 BM-156

    SUBJECT: BM-156
    SYMPTOM:
    BM-156.
    CAUSE:
    Open circuit in the interlock system.
    SOLUTION:
    If a trimmer or Cover Feeder is not being installed in the Booklet maker, an Interlock Jumper needs to be...
  12. [CQ] Re: Ricoh FW760 Wide Format toner streaking, ghosting, etc.

    I'm not sure of the location on these older units, but the newer wide format machines have a release lever on the bottom right side of the drum. This moves the cleaning blade away from the drum for...
  13. Re: MP4000 jamming but not logging in data log

    Actually, it will show the jam but it will be logged as 001 power on jam. I've also had to replace the push switches for the side door and front door switches on some models. Since it's got the...
  14. Replies
    5
    Views
    3,623

    Re: Aficio 2018 scan to email setup

    1256312564

    Here's the white papers on setting up scan to email and scan to folder.
  15. Re: 2228C black and white blurry prints and copies

    I'm confused a bit as your title and message seem to contradict themselves, but here's a shot. If it's just the black images you're having trouble with try replacing the pcu and developer for the...
  16. Replies
    11
    Views
    1,590

    Re: Aficio 1224c poor prints

    Don't use it as a door stop, someone is likely to plug it in and use it. I suggest boat anchor or wrecking ball.
  17. Re: Ricoh mpc 2800 load cyan toner cartridge message

    Try replacing the developer if it's over life. If not, you'll probably need to replace the entire dev unit. Also check out TSB #018 for that model. There are part number changes for the pumps and a...
  18. Replies
    7
    Views
    939

    Re: Problems with Savin 2070 ADF

    What are the jams codes in your smc reports?
  19. Replies
    7
    Views
    939

    Re: Problems with Savin 2070 ADF

    The specific jam codes will be helpful in giving an accurate recommendation.

    Have you replaced the feed clutch in the ADF?
  20. Replies
    11
    Views
    6,489

    Re: Gestetner MP171SPF & Gmail SMTP

    You can set up the scanned files to be sent as .tif or .pdf documents.
  21. Replies
    9
    Views
    1,412

    [Misc] Re: Printing with user's identity MPC3500

    If they aren't picking up print jobs right away, you could suggest using the lock/hold feature in the print driver. This would hold the jobs until the customer comes up to release the jobs and save...
  22. [Error Code] Re: Error Code BM-004 on SR90+ Plockmatic Booklet Maker

    That is not a valid error code for the BK5010.

    Here is the error for BK-004 from the SM.

    BK-004
    Fault Code BK-004, indicates that the Back jogger motor (BK-M2) had a Cycle time out.
    Initial...
  23. Replies
    11
    Views
    6,489

    Re: Gestetner MP171SPF & Gmail SMTP

    Read this thread, specifically post #6 and #9. Also learn to use the SEARCH FUNCTION.
  24. Re: Richo Scanrouter V2 "Launching of the scanner driver "

    Being able to scan from the MFP seems like a reason to change to S-t-E, but that's only my opinion. If you can't get Scanrouter working again your only other options are new MFP's or to eliminate the...
  25. Re: Richo Scanrouter V2 "Launching of the scanner driver "

    Try disabling any firewall (Windows or otherwise) and disabling all virus software for testing. What OS are you running? I know it was never supported with Vista or Win7.

    You can give this a try...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4