STOP!!! The CW2200 WILL NOT PRINT IF THERE IS A PAPER MISMATCH!! Be Absolutely certain that the Wide Format paper type in Roll Feed 1 (or 2, depending where your printing from) is an exact match for...
Type: Posts; User: Gary Bowen
STOP!!! The CW2200 WILL NOT PRINT IF THERE IS A PAPER MISMATCH!! Be Absolutely certain that the Wide Format paper type in Roll Feed 1 (or 2, depending where your printing from) is an exact match for...
Just for the record the Type 8000 Print/Scan SD Card is unique to the D052 series only which is the MP 6000. The correct Print/Scan SD Card for the MP 7500 is G338 (which is the Type 1075).
You are far too accommodating with your customers. The last time I had a Feeder problem similar to this a tech had already done a preliminary call. When I went in I made sure I had a sample set of...
Have you tried adjusting the Buckle with SP 1003-002 for Tray 1 (Plain)? I know you said all 4 Trays exhibit the same problem but its worth a try. Tray 2/3/4 all are adjusted with SP 1003-007 (Plain).
You may want to reseat Controller PCB, NV RAM, DIMMS, FAX. Is a HDD installed and have you tried starting it up without the HDD? What is the frequency of the error. SC 672 is a very common (and...
SP5875 (set to 1) will disable SC Auto Reboot. If SC Auto Reboot is disabled then the SC code will appear on the screen. SP 7403 will tell you what the Service Code was that generated this reboot. Go...
On the CW2200 this could normally be resolved by replacing the Encoder Strip which you have already done on this machine. Did you remember to remove the Mylar backing sheet that is on the Encoder...
These are the 2 Technical Bulletins referred to in this post. No where do I find that there was any Engine or System/Copy Firmware updates that addressed this problem?
AX040256 DC Motor-LCF
Sounds like you did a mini "refurb" when the machine came in? Did you verify Print/Scan worked when you got the machine or are you assuming it worked? I do a fair number of refurbs and have in the...
Your current SOP Package firmware is a very old version (15.2). The current SOP Package firmware is D1465519N (v27.00), so there is actually a version newer than the one you plan to update. There...
I agree with guitar9199 in regards to the Controller PCB being at fault. These boards seem to cause multiple errors - still. Just had 1 in May throw the 2 codes SC878 and then SC672. The first...
Have the same problem with these little gems that you are experiencing. Some feeders (and not all of them) create quite a noticeable vibration from the Feed Head/Separation Pad contact -this occurs...
One of my least favorite machines to work on. Some things to get you started. What is the mileage on the machine? At some point you will need to replace ALL the parts in the Roll Feed Assy - Feed...
Depending what you need to replace the Touch Panel (D0091488) and VGA Display (D0891498) are the same for the C3501 and C4501. If D0091488 looks familiar it is the same Touchscreen as for the MP...
That is a good point slimslob makes. You didn't mention the meter count on the machine, the PM count or how long the machine was in storage? But go with the cheapest and fastest fixes first. PCDU's...
The problem copy is on the right side not the left (at least when I download it). It looks like you described - a copy output from a low resolution printer. Couple of things I would do: (1) Print...
Expected yield of the Fuser Cleaning Web (AE045069) is 450K, which is part of the PMD131450K PM Kit (Fuser PM Parts).
Ouch!
$1.30 CAN is approx $2 US. How much is $79 BRL in US dollars? Again, what is your original error/ jam code? You are probably headed in the right direction - sensors do fail but the more info you...
As with any Ricoh MFP make sure all your firmware is up to date. Secondly, the '04 series uses the same Rising Motor (AX040273) as the '03 series colour. Your paper height is actually determined by...
I stand corrected. The sensor is $1.30 (CAN) on myricoh.
This sensor is around $2 (CAN). Why are you wasting your time wanting to test it? What is your actual problem that has you going down this "rabbit" hole?
Machine was locked up when I arrived. it would NOT allow me to: (a) Enter SP Mode or (b) Update Firmware. The original Controller PCB would not work when tested on a second machine - same problem....
FYI. Had a call for a SC878-01 error with the machine completely locked up. Installed a known working Controller Board and then the machine went to a SC672 error. Ordered in a new Controller PCB...