Search:

Bad cq so I run a partial sky shot and 2/3 of the page is black and 1/3 of page has white and black linesfrom one end to the other side to side of the 8 1/2 inch direction possibly the saw tooth?

It just wipes off w/o any problem, it's not like it is fused in, it's just charged to the core. no problem of it coming off

I know I hate using katun drums but thats what my company uses, but I dont think that the drum is at fault in this case since I replaced the drum and the same exact problem came back within 200...

I will check into dev. change but cleaning the drum does no good cause its ruined. There are like tiny chip all over it the layer on the core is chipped off somehow. so when you clean the toner off...

I have two 507 copiers that both machines , the drums have small spot of toner ahered to them and when you wipe off the toner the drum coating is gone. I thought this was a bad drum issue since they...

Thank you so much for the tip, I will give it a try. Hope all is going well for you

I have had this problem twice and now my 3rd goat it again. L3 code with scanner advancing 4 to 7 inches and stops resulting in copy with lines instead of print. I have replaced scanner board and...

Thanks to everyone

Hey out there, can anyone help me fond the part # for the document feeder sp2 model that goes on ar160/200 units. The parts I am looking for are the doc feed roller, the pick up roller and the...

I have a ar651 where the very 1st page is clean but with each additional page in lets say a run of 20 copies the background gets progressively worse. unit has 200,000 and factory toner. I do not do...

This 651 starts with a clean copy and as they print out they get more and more background. The copier has 200,000 pages on it and useing factory toner. I am not real familer with this unit so all the...

Thanks Mate, this has been alot of help. Actually, Thanks to u all

The gear on the drum is ok it is the gear that drives the drum, coming from the rear of the frame. Have you ever replaced this gear? In the part book it shows a ring that looks like it secures the...

Derrick, go down the street to the electronic store and you will find it there, But dont forget to check with MT first b-4 you spend any cash!!!!!!!!!!!

Thanks WAZZA, I am ordering a yellow cart. esp since the gear that turns the drum for the yellow turns out to be cracked

Can someone help me with part # for drum drive gear for sharp BC320

On the duplex module you may want to check for cracks where the bearings fit into the sides of the unit. this will cause all kinds of jamming headaches. you can get a fix from sharp for this but the...

Thanks M. I will be there in the morning and will be looking for all you and Blackcat have pointed out

Blackcat, Your reply to my issue sounds right on but you are stating 2.5mm on a 260, where as my problem is much larger than 2.5 mm, I am seeing about 1 inch. The 6.81 inch sounds about perfect. So...

During copy process you will hear a noise that sounds like a toner mtr activation that seems to coincide with a one inch voided line going from side to side if running letter-r, by voided I mean say...

Went back to the job on tuesday and found some grease and toner on the springs for the main corona, after I cleaned them and ran 25 copies it all tested ok, but as I said it is intermittent and I am...

I have replaced drum, transfer corona, blade I will go out there and check 64.01 and will have a main corona w/me. I would have replaced the main corona the first time but did not have one. I will...

This fuzzy line goes across the page and is 2 to 2.5 inches from the true lead edge, meaning as the copy exits the fuser the lead edge is coming out first then measure down and it can be very dark...

This copier is on a dedicated line with a constant 122 V. and on a surge protecter. This is one of those nightmares, you know, you have 3 to 4 weeks of great calls then you have 2 weeks of...

about 3 weeks ago I had posted this problem of a AR 337 on the Lcd when turning on the copier the logo would come up and then freeze w/o a warm up, nothing. It was at first intermittent then...