I have had an issue similar to this with a C220, try adjust the wren value and the line type.
Type: Posts; User: huntergazz
I have had an issue similar to this with a C220, try adjust the wren value and the line type.
Thanks very much for the info mr bill. Was also wondering where to get parts from.
Thanks very much :)
Hi Guys,
Dows anyone have access to a service manual for an HP Laserjet 4, I know its an old one now, but Im looking after this model on behalf of a charity youth group who dont have the money to...
Thanks for the info Jomama, i will keep that in mind. Its a weird one, I would not have thought about a printer driver causing jamming in that way.
Thanks Very Much!
Hi Guys,
Thanks for the help on this. It was a driver fault. Rolled the driver back to pcl5 and so far so good.
Thanks
Hi Jomama,
I have removed paper from tray 1 as the guides are faulty and im not paying for a new tray. all the paper is in tray 2, altho not filled up as i found that if you fill the paper too...
Hi Guys,
I have an issue with and Aficio 3224C jamming on all trays when printing.
There is an element of damp paper involved, but if you copy it will print 100 sheets no problems. However...
Hi Guys,
I have had this problem quite a few times on the 220, 280 and 360. 9 times out of 10 I have resolved by backing up all the settings, performing a full format of the hdd and then a...
I had this problem with a C203 a few months ago. turned out to be the laser control board.
Thanks for the tips so far, but no joy.
The plate that moves the dev unit is fully engaging on the drum and as far as i can tell its all turning. The dev lever is at the 9 o'clock position and...
Hi Guys,
I have an issue with a canon GP225 that is printing blank copies. I have added toner and changed the drum with no joy. Is it a possible hv issue? I have not got any previous...
Hi,
I had a similar issue with a 203, I replaced the mfp board then when I loaded the f/w it took an age to boot up again. It turned out that the version of the f/w I had was out of date. I...
Hi,
Have you tried aligning the screen? cd error are usualy memory issues (firmware, hdd, memory dimms, files sent to print / copy / scan.)
Hi,
On the door there is a roller with a gear on the left hand side. Check that the roller is in good condition, check that the gear is intact and the pin inside the gear is still there. i have...
Hi,
I have not seen this problem with the belts. The common one I have seen (10-15) is where the sep claw punctures through the belt, gives a mark on the print that looks similar to a staple. ...
Hi,
This may seem a little basic, but when you replaced the developer and drum etc did you perform the function of F8 in the service mode?
got a call from a customer to report that the fax was not recieving...... sent a test fax to them and she sent it back all ok... the next day she calls back with the same fault, but she explains...
Hi,
I have had 30-40 Machines with this problem!! I take the following measeures and I have only had to replace 2 feed stations
1 - Strip and clean the clutch, Its usually rusted up (Faulty...
Hi Guys,
we get all ours from copier chips.co.uk. You can reset the belt and fuser in the service mode but not the drums.
Hi,
The error code C225B is referring to the motor that drives the k pc drum. its either not turning / turning abnormally. I would change the motor, if not then you problem is with the printer...
Hi,
Im not 100% about the C250, but the newer machines require an extra add on to the machine (SC-507).
Hi,
You can also access the service mode by turning the machine off at the keypad then the main power switch behind the front door.
then...
turn on the keypad switch
hold utility counter...
Hi,
when you click on autocolour it will bring up a manu where you can select black only. After selecting this you press utility counter > user settings > copier settings > default settings >...