Search:

Type: Posts; User: The Otrain

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. [Misc] Re: Sharp MX-B401 Does Not Pull Original Immediately

    :confused: Whoa....now that might be a problem. Anything on IDNC? Firmware up to date etc.?
  2. Re: Have your service meetings become sales meetings?

    A meeting? It is a "tongue-lashing", reminding you when you screwed up in the previous 2 weeks or so. Sometimes, they feed the animals too!
  3. Re: Canon IR3300 Printer/Copier Tech - Wilmington, NC

    Did you ever get this done? If not, send me a pm. I am in Fayetteville, not too far.
  4. [Misc] Re: Sharp MX-B401 Does Not Pull Original Immediately

    Isn't first copy time using the RSPF about 10 sec with this model? I thought that was normal.
  5. Replies
    7
    Views
    1,920

    Re: Sharp user Codes (How to set up)

    There are so many options as previously mentioned. You can even set it for color authentication only and allow unlimited B/W usage. If you are interested in that, check the TT-20003 on the IDNC...
  6. Replies
    9
    Views
    15,402

    Re: Sharp copier simulation

    No. Almost all models have different codes/sub-codes. Best bet is to get a manual for a specific model.....especially if it is an older one.
  7. Replies
    20
    Views
    5,327

    Re: CATRIDGE ! IMMPORTANT ! + nude pics

    Amen to both of those comments old brother......Maybe we should send pics of a "service manager of your's and his girlfriend"....Haha!
  8. Replies
    3
    Views
    1,221

    Yes, very common for someone to place books or...

    Yes, very common for someone to place books or other originals on the right sensor and then have that message pop up. Make sure that sensor works as well using your SIMs.
  9. Replies
    2
    Views
    11,874

    It is a lot faster if you have a laptop and can...

    It is a lot faster if you have a laptop and can direct connect with crossover cable. You can get code reset in seconds.
  10. Thread: Office 2007

    by The Otrain
    Replies
    10
    Views
    3,440

    That's it. Sometimes it will also have an issue...

    That's it. Sometimes it will also have an issue with Outlook 2007.
  11. Replies
    9
    Views
    1,125

    Haha. At least you were able to get it going. ...

    Haha. At least you were able to get it going. If it wasn't on Bragg, I doubt the customer would have even attempted the repair.
  12. Replies
    2
    Views
    2,164

    Sorry, not available. Just checked the Sharp...

    Sorry, not available. Just checked the Sharp tech site.
  13. Thread: MX-2300

    by The Otrain
    Replies
    10
    Views
    1,966

    Yes, it could be bearings causing flat spots on...

    Yes, it could be bearings causing flat spots on rollers.
  14. Thread: pls help

    by The Otrain
    Replies
    6
    Views
    1,180

    [Misc] What model?

    What model?
  15. Replies
    1
    Views
    2,425

    Open the windows printer page. Right click on the...

    Open the windows printer page. Right click on the Sharp. Select Properties or Printer Properties (depending on which version of windows you are using). Select tab on top right hand corner...
  16. Replies
    7
    Views
    10,619

    Sharpdesk is NOT needed to set email scanning. I...

    Sharpdesk is NOT needed to set email scanning. I would double check settings as mentioned earlier, especially authentication set up.
  17. Replies
    18
    Views
    4,123

    Running the exe is always the easiest way to go...

    Running the exe is always the easiest way to go for Sharp Drivers. (As noted, he beat me to the punch.)
  18. Replies
    3
    Views
    1,713

    ...Also, make sure to add the email address to...

    ...Also, make sure to add the email address to the address book 1st, and then set up the inbound routing. Once address is set for inbound routing it cant be edited or deleted unless you turn inbound...
  19. Replies
    14
    Views
    4,528

    Just a side note. Sharp has been replacing a lot...

    Just a side note. Sharp has been replacing a lot of these fusers under warranty because of the issues. Might want to check into it.
  20. Sounds like you have an IP conflict. Set the...

    Sounds like you have an IP conflict. Set the copier to DHCP/Dynamic and see what address it picks up. More than likely, something else on the network has taken the same IP that the Sharp was using...
  21. It could be the firewall/windows defender. Also,...

    It could be the firewall/windows defender. Also, check to make sure that no "odd" free virus protection is running. That's what was giving me that problem until I turned off defender.
  22. Replies
    29
    Views
    61,190

    Wow. I take it people hate Runz. Some of our...

    Wow. I take it people hate Runz. Some of our techs use it and the majority of the them seem to like it. I personally have no problem with it. Maybe it is the plan my company is using, but I make...
  23. We recently switched from Bomgar to Team Viewer. ...

    We recently switched from Bomgar to Team Viewer. Seems to be doing well so far, though i have only used it about 4 times. Our internet connection at our local office was shabby, so I'm sure that...
  24. Replies
    7
    Views
    2,236

    I had the same problem. It's good to know that I...

    I had the same problem. It's good to know that I wasn't going crazy and others have been facing the same issue. What i did was lube the drive gears.....almost all of them with some "Tri-Flo" lube. ...
  25. Replies
    19
    Views
    4,387

    Crossover cable will work if you are connecting...

    Crossover cable will work if you are connecting it to just one PC. DO NOT install the print driver until the Sharp is configured (IP address etc). Sharp print drivers will find the printer...
Results 1 to 25 of 54
Page 1 of 3 1 2 3