Don't know if you all know.. HORSE has left KM.. Sad to see him go.. Great bloke
Type: Posts; User: doma873
Don't know if you all know.. HORSE has left KM.. Sad to see him go.. Great bloke
Thanks for that.. I'll give it a go
Hi All
I have an issue with a C500 printing SRA3 to the sub tray of the finisher. The client wants it to print to the main finisher tray.
I thought there was a dip swich to do this but can't...
Hi All
I have a KM BH 1050 Jamming when doing booklets in the SD-501. It comes up with J72-90. It only occurs when trimming is turned on. Non trimming works fine. The Manual say PS55 could be an...
I would also try running test pattern 0 and just do 255 density of yellow. If its grainy and feels like sand paper replace the (y) dev..
Have you replace the sensor???. It is part of PM kit 3 so should be changed every 3million prints. Also if you have just done a PM make sure you have pluged it in.
Hi All
I have been working on a C6500 that has a SD-501. Only sometimes when doing A3 books one of the sheets scew when folded. Its only about 2mm but very noticeable. I have ordered folding...
Its need a new cleaning blade. They were the same as 2028 3035 4045 series and 3135 etc.
There quite easy to change. Must use setting powder
I heard today that the DU102C will be available soon.
I am 100% sure the drum coupling which is moulded in the drum is different, That is what drives the drum. Also the drum housing is different. I don't think your drums will be changed today :-)
We have been putting the c500 app roller in here in canberra with great sucess. Thanks to the guys in Brisbane for a solution. I hope the new drums we are getting this week will work.
Why would you get image from under scan plate when its a digital and the optics only read the image?? Just a thought.. I have have rego clutch problems and have never seen that!!!
I Have had in the past the ozone filter in the rear of machine behing the fuser clog up and cause the image process board to over heat and cause this issue. Check the filter and replace it. Its...
I would do the above first. I have also had a faulty Dmax sensor cause this problem also. Make sure the sensor is very clean. If you check the service code counter you may see a few dmax errors...
Is this ment to be funny or just a joke. The above quote is to reset F34 , 35, 36 codes that relate to fuser error. Nothing to do with reseting PM counter.
Now for an old trick. If you haven't...
I look after losts of 1050's and I would reconment adding the RC-501. I have had simular problems and i will list a few ideas to try.
1) Clean the Dmax sensor under the cleaner unit with alchole...
F26-1 is a L detect error for the dev. It could be a few things. First try a new dev and run l detect in 36 mode. If the error is still there try a TDS sensor. I have also have had the toner hopper...
Geezzzz
When i was working on 7033 -40's this was most common problem. The current running through the swich is to high. When you clean or replace the switch bend the housing plate foward and...
Thanks for all your advice. I ended up getting another fiery to test and had no fault so must be the fiery. I will investigate the fiery and reload firmware and re-check internal connections.
Hi All
I have a C500 with a fiery ic901. What is happening is when you print a document in any application it will randomly inverse the image (Like a negitive). eg you can print the same document...
Just a thought. What if you connect 2, 7075's as tandem and print from one controller. Been too long for me since i have setup this model, but it may work. Anyway its not really what you wanted i...
When you configure the fiery remember to turn on port 9100.. This is common problem as it is turned off by defalt..
Hi
When you IP601 is connected to the 7075 turn the 7075 on and after about 5 minutes the machine will print a config page with ip adress etc....
You can the log into the ip601 through a web...
Have had NVRAM do this before. I would try it first the look at board..