Search:

Type: Posts; User: suso73os

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    1,746

    Re: Bizhub350 Developer problem

    I haven't changed any ATDC sensor in this model but may be of course, in my opinion de problem are the solenoids, there are two, one for the toner bottle and other for the toner hopper, when they...
  2. Replies
    3
    Views
    899

    Re: Bizhub C450 exit sensor (PC30) problem

    Check the service manual to see the diagram, you can follow the cables but it could be sometimes a bit hard.
  3. [Misc] Re: Bizhub 200 Where is the Documnet Transfer Belt?

    Could you scan a copy with the problem and upload to this forum please, it would be really helpful.
  4. Replies
    12
    Views
    1,746

    Re: Bizhub350 Developer problem

    The problem may be the solenoid that turns the toner bottle and the hopper unit, over the time the sponge that has the solenoid becomes like glue, for this reason the toner bottle or the hopper unit...
  5. Bizhub C6500 Vertical lines, not consistent colors.

    Hello, I have a bizhub c6500 with vertical cyan and orange line and non consistent image, I have changed coronas, second transfer roller and cheked transfer belt, drums and developer units but I...
  6. Replies
    1
    Views
    759

    [Error Code] Re: W2522 Oce' machine has error 2151

    Hello, c2151 is a second transfer roller problem not a transfer belt problem, second transfer roller is situated in the right door, I have found a service note that talks about the second transfer...
  7. Replies
    4
    Views
    910

    Re: bizhub C250 C350 need some comments

    No, you can't put a color drum into the black drum hole, you can buy a new chip only if you don't want to buy a new imaging unit.
  8. Replies
    3
    Views
    3,056

    Re: konica BIZHUB C35 (TONER C ANY K MISSING)

    Yes, I had the same problem I few months ago and was the pins that read the toner chip.
  9. Replies
    22
    Views
    26,708

    Re: Konica Bizhub C220 C2 Firmware Setting

    Hello all, I'm a photocopier technician and I Develop autorized dealer (ineo plus 451, ineo plus 203, ineo plus 452, ineo plus 220, etc) these machines are the same than Konica Minolta but As I can...
  10. Replies
    15
    Views
    2,684

    Re: How to chip a C220 imaging unit?

    Hello all, I'm a photocopier technician and I Develop autorized dealer (ineo plus 451, ineo plus 203, ineo plus 452, ineo plus 220, etc) these machines are the same than Konica Minolta but As I can...
  11. Replies
    3
    Views
    7,591

    [Error Code] Re: c-2556 and c-2551

    I think itīs a toner issue, check toner input mechanism, mylars and motors.
  12. Replies
    12
    Views
    7,222

    [Error Code] Re: Konica minotla bizhub 250

    Sorry, I paste what I found, I donīt know if you can see it or not.
  13. Replies
    12
    Views
    7,222

    [Error Code] There are several service notes talking about a...

    There are several service notes talking about a similar problem, I donīt know if you can access to these.


    When turning ON the power or during operation,...
  14. Thread: bizhub 601

    by suso73os
    Replies
    3
    Views
    1,330

    The display will not continue beyond the...

    The display will not continue beyond the hourglass screen at power up.


    [Solution]
    ...
  15. Replies
    29
    Views
    6,899

    There is a service note: The...

    There is a service note:

    The display will not continue beyond the hourglass screen at power up.


    [Solution] ...
  16. Replies
    16
    Views
    7,396

    [Electrical] Hello, about the error code I found this in a ...

    Hello, about the error code I found this in a Ineo 250+ manual : Due to the memory access failure, when a large size job is sent to the machine, the Trouble Code CF023 appears on the Massage...
  17. Replies
    7
    Views
    1,561

    [Misc] May be an MFP board problem or nvram problem,...

    May be an MFP board problem or nvram problem, check conectors, change MFB board if you have another machine or the posibility to obtain one, I had a problem with the control panel cable but the lcd...
  18. Thread: Bizhub 250

    by suso73os
    Replies
    11
    Views
    2,777

    I had a similar problem and I solve it resetting...

    I had a similar problem and I solve it resetting fax parameters.
  19. Replies
    12
    Views
    3,012

    Ok, Iīm sorry for the mistake but I donīt speak...

    Ok, Iīm sorry for the mistake but I donīt speak english very much.
  20. Replies
    2
    Views
    1,956

    Do you have the service manual?, I canīt find...

    Do you have the service manual?, I canīt find this error on it.
  21. [Misc] I found a similar problem some time ago, When I...

    I found a similar problem some time ago, When I got to the client house I saw that the waste bottle was full (I donīt know if you found the same problem), there is a small tube between the transfer...
  22. Replies
    12
    Views
    4,304

    I have found a service note for this problem,...

    I have found a service note for this problem, Hope it helps.



    C2257 at power ON.


    [Solution]
  23. Replies
    12
    Views
    3,989

    [Misc] I resolve the same problem with the nic reset...

    I resolve the same problem with the nic reset tool firmware, Itīs a pity that it donīt work for you, but if the problem persist the problem may be the motherboard.
  24. Replies
    12
    Views
    3,989

    [Misc] Yes, as Mr spock said there is a special firmware...

    Yes, as Mr spock said there is a special firmware that you can use to reset the Nvram and Nic separately, so you can reset all nic parameters, I did it 2 weeks ago in a Develop 451+ that had the same...
  25. Replies
    12
    Views
    3,012

    After you change any laser unit you can use an...

    After you change any laser unit you can use an special firmware for this machine to solve the laser error code and see if an error code reappear or not.
Results 1 to 25 of 38
Page 1 of 2 1 2